Display; Operating Mode A; Temperature; Programs - IKA EUROSTAR 100 control Operating Instructions Manual

Temperature:

In the "Temperature" menu the user can specify that the tem-
perature sensor is displayed on the display/working screen. A tick
shows that the option is activated. The precondition for this is that
a temperature sensor is connected to the EUROSTAR station. If
no temperature sensor is connected, or an error is present or the
temperature rises above 350 °C, three dashes are shown as the
temperature value.
Note: Please comply with the temperature measurement range of
the external temperature sensor specified in the "Technical data"
section. The temperature display can be in either °C or °F (see the
"Settings" menu).
Timer:
In the "Timer" menu the user can specify that the timer is dis-
played on the display/working screen. A tick shows that the option
is activated. This setting allows the user to specify the actual time
for the stirring procedure.
A default time can also be set for the timer. This setting allows the
user to start the stirring task for a standard time. The device stops
automatically after expiry of the set time, and the set time used for
the stirring procedure appears in the display.
Note: The user can stop the stirring function before expiry of the
set time. In this case the countdown of the timer is interrupted.
Operating Mode:

Operating Mode A:

In this operating mode, the set speed is not saved when the current
run comes to an end or the device is switched off.
Operating Mode B:
In this operating mode, the set speed is saved when the current
run comes to an end or the device is switched off, and the value
can be changed.
Operating mode C:
In this operating mode, the set speed is saved when the current
run comes to an end or the device is switched off, and the value
cannot be changed.

Display:

In the "Display" menu the user can specify what information will
be displayed on the main screen.
Note: If the "Torque"option is activated, by pressing the "Back"
button the user can reset the current torque to 0 Ncm as a reference
value. At the same time the Δ appears in front of the Ncm unit.

Programs:

Under menu "Programs", 5 user-defined speed (rpm)-time pro-
files can be created. In addition, the user could define the intermit-
tent mode is activated or not in the programs.
If the intermittent mode is activated, the run time/stop time value
from "Intermittent Mode" setting will be taken.
Note: If user need to activate the intermittent mode in one segment
of a program, he should set the "Run time/Stop time" in menu
option "Interval", meanwhile activate the "Run/Stop" function in
menu option "Intermittent Mode" (see section "Stirring").
Once a programs has been selected, the following options are avail-
able.
Start: Start the selected program upon request.
When the selected program is started by pressing on menu option
"Start" with rotary/push knob, screen reminds the user to confirm
the program control. Press "OK" with rotary/push knob to start
the program control.
Edit: Edit the selected program parameters.
Start to edit the selected program parameters by pressing on menu
option "Edit" with rotary/push knob. The user can edit, delete or
insert one selected program segment in the program.
When user edits the program time for at least one segment, tick (
for respective program will appear.
Delete: Deletes the selected program.
If a selected program is deleted by pressing on menu option "Delete"
with rotary/push knob, all the program parameters will be emptied.
√
The tick ( ) disappears.
Details for editing the program:
When a program is being edited, following screen appears.
In this program, user can define up to 5 seg-
PROGRAM 1
ments. The selected segment is highlighted.
Seg rpm Time Interm.
No hh:mm Mode
.
Then, the user can edit, delete or insert a
1 0 00:00 No
segment in this program.
When the "Back" button is pressed after
2
editing, the program is save automatically.
3
4
5
Edit Delete Insert
Edit:
When the highlighted "edit" symbol appear on the right top of
the screen, the user could change the speed (rpm), time value or
intermittent mode setting.
Note: The speed (rpm) value can be changed during the speed
limit range of the device. The time can be set from 1 minute to
10 hours.
Delete:
When delete a highlighted segment, the settings will be emptied. The
section jump to next segment.
Insert:
With the insert option, a new segment will be insert below the
selected segment. The default settings for the new segment are as
following:
rpm: 0
Time (hh:mm): 00:01
Intermittent Mode: No
√
)
13