Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for OPERTIS eLOCK eXpress
Summary of Contents for OPERTIS eLOCK eXpress
- Page 1 Installation and operating instructions Antenna in the Siedle housing ES314.2001...
-
Page 2: Table Of Contents
Contents Introduction ........................4 About these instructions ....................4 Explanation of the symbols and signal words used............4 Target group ......................... 4 OPERTIS Support ......................4 Up-to-date information....................5 Product Description ..................... 5 Overview ........................5 Operating principle ....................... 5 Signalling ........................ - Page 3 Installation and operating instructions Antenna in the Siedle housing Technical data......................23 Disposal ........................24 Product........................24 Product packaging ..................... 24 Notes:......................... 24 OPERTIS 3 12/2014...
-
Page 4: Introduction
Antenna in the Siedle housing Installation and operating instructions Introduction About these instructions These instructions contain important information and instructions for installation operation of the wall scanner antenna in the Siedle housing. Read through the instructions carefully before starting the installation work and putting into service. -
Page 5: Up-To-Date Information
This ensures the greatest possible protection against manipulation. The management and programming of the terminals, including the issue of access authorisations, is carried out using the eLOCK eXpress management software. OPERTIS 5... -
Page 6: Signalling
Further information on the product is given in Section 11 "Product specification". Intended Use Area of use The antennas are only used together with OPERTIS controllers. The antennas are suitable for installation in the Siedle door intercoms, Vario and Compact series. Combinations of the wall scanner products:... -
Page 7: Condition Of The Product
Note! In general, avoid laying the cables in the immediate vicinity of noise sources. Always use a shielded cable in ambient conditions with EMC disturbance. If you have any questions, please contact OPERTIS Support. OPERTIS 7 12/2014... -
Page 8: Residual Risk
It is then only possible to open the door using mechanical tools. In this case, contact OPERTIS support. If an antenna is used for access control to a fuse box there is a risk of being locked in or out if a fuse is defective. -
Page 9: Safety Instructions
Antenna in the Siedle housing Safety Instructions The following safety instructions must be noted and followed before use! OPERTIS does not accept any liability whatsoever for personal injuries or damage to property caused by failure to follow these instructions! CAUTION... -
Page 10: Scope Of Supply
Antenna in the Siedle housing Installation and operating instructions Scope of supply The scope of supply includes the following parts: Part Name ES314.2001 Antenna in the Siedle housing Device screw (4 no.) Installation Overview The installation is divided into the following activities: ... -
Page 11: Connection At The Controller
Immediately following installation you should program the authorisations to prevent unauthorised access; refer to the eLOCK eXpress Quick Start Guide. Have the date and time reset, if necessary by your eLOCK eXpress trade partner. Connection at the controller... -
Page 12: Connecting Additional Antennas
Antenna in the Siedle housing Installation and operating instructions Pin assignment The following connections must be connected for the connection of the antenna with the controller. Connection Connection Antenna connection description Controller Bus 1 Bus 2 RS485_B Bus 3... -
Page 13: Functional Test
Installation and operating instructions Antenna in the Siedle housing Figure: front of antenna Signalling LEDs Terminating resistance (ON position is labelled.) Functional test CAUTION Risk of being locked in or out Peripheral devices cannot be controlled without functional controllers and without a functional antenna. - Page 14 Antenna in the Siedle housing Installation and operating instructions Proceed as follows: Step Activity Result Switch on power Initialisation processes: supply. The controller sets up communication with the connected antennas, duration max. 15 seconds. Signalling to the...
-
Page 15: Operation And Control
Optical signalling is switched on by default. A buzzer can be switched on optionally for the acoustic signalling. All optical and acoustic signals are given in the eLOCK eXpress system documentation. In case of certain system states and events the wall scanner emits... -
Page 16: Maintenance, Cleaning And Care
Carry out functional checks while the door is open. The following functional tests are to be performed once a year, if necessary by the eLOCK eXpress trade partner: Step Activity Result... -
Page 17: Dismantling
Installation and operating instructions Antenna in the Siedle housing Dismantling Note Dismantle in the reverse order. Therefore, refer to the figures in Section 6 "Installation". Proceed as follows: Step Activity Figure Switch off power supply. To remove the antenna, the... -
Page 18: 10 Problems And Solutions
Antenna in the Siedle housing Installation and operating instructions 10 Problems and Solutions Problem Possible cause Solution Antenna has no Power supply is Ensure power supply. ready signal. defective or not connected. Connection cable to the Ensure connection to antenna is defective or the antenna. - Page 19 Installation and operating instructions Antenna in the Siedle housing Problem Possible cause Solution Antenna is not Termination resistances Set the termination detected by the set incorrectly. resistances correctly. controller. Each transponder is Wall scanner is not Program the wall...
-
Page 20: 11 Product Specification
Antenna in the Siedle housing Installation and operating instructions 11 Product Specification Declaration of Conformity Konformitätserklärung gemäß dem Gesetz über Funkanlagen und Telekommunikationsendeinrichtungen (FTEG) und der Richtlinie 1999/5/EG (R&TTE) Declaration of Conformity in accordance with the Radio and Telecommunications Terminal Equipment Act (FTEG) and Directive 1999/5/EC (R&TTE Directive) - Page 21 Installation and operating instructions Antenna in the Siedle housing Schutzanforderungen in Bezug auf die elektromagn. Verträglichkeit § 3 (1) 2, Artikel 3 (1) b)) Protection requirements concerning electromagnetic compatibility § 3(1)(2), (Article 3(1)(b)) angewendete harmonisierte Normen: Einhaltung der grundlegenden Harmonised standards applied...
-
Page 22: Dimensions
Antenna in the Siedle housing Installation and operating instructions Dimensions All dimensions given in mm. Rating plate Note on the Operating System The antenna is operated with the FreeRTOS operating system. Further information under: www.freertos.org 22 OPERTIS... - Page 23 Installation and operating instructions Antenna in the Siedle housing Technical data Installation environment Design Siedle colour scheme (white, silver metallic, titanium metallic, graphite brown metallic) Installation environment Siedle Vario / Compact intercoms Installation distance between at least 100 mm in 3D space...
- Page 24 Product Disposal in accordance with WEEE Directive 2012/19/EC: Do not dispose of product in the local household waste. Send product back to OPERTIS or dispose of it at a communal collection point for hazardous electronic wastes. Product packaging The product packaging must be disposed of through the local household or paper waste collection facility.
- Page 25 Installation and operating instructions Antenna in the Siedle housing OPERTIS 25 12/2014...
- Page 26 Antenna in the Siedle housing Installation and operating instructions 26 OPERTIS 12/2014...
- Page 27 Installation and operating instructions Antenna in the Siedle housing OPERTIS 27 12/2014...
- Page 28 Germany OPERTIS GmbH Prof.-Bier-Straße 1-5 34454 Bad Arolsen Telephone: + 49 5691 87741-200 Telefax: + 49 5691 87741-310 support@opertis.de www.opertis.de MB314.02EN V001 12/2014...
Need help?
Do you have a question about the eLOCK eXpress and is the answer not in the manual?
Questions and answers