Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Tarter MS1002
Summary of Contents for Tarter MS1002
- Page 1 OPERATOR’S MANUAL MANURE SPREADER MS1002 WARNING: Read understand this manual before operating the equipment. Failure to follow the instructions and safety guidelines contained herein could result in personal injury or damage to the equipment. 4000007 | REV 4 TA R TE R U SA .COM...
- Page 2 Please read this manual before operating your Tarter product and keep it handy for reference. Require all operators to read this manual carefully and become acquainted with adjustments and operating procedures before attempting to operate the equipment.
-
Page 3: Table Of Contents
CONTENTS TABLE OF CONTENTS INTRODUCTION PRODUCT DESCRIPTION SAFETY INFORMATION SAFETY & INSTRUCTION DECALS ATTACHING OPERATION DETACHING MAINTENANCE STORAGE SPECIFICATIONS TROUBLESHOOTING PARTS TORQUE SPECIFICATIONS WARRANTY This Operator’s Manual should be regarded as part of the machine. Suppliers of both new and second-hand machines must make sure that this manual is provided with the machine. - Page 4 DESCRIPTION Tarter’s Manure Spreader attaches to nearly any garden tractor or ATV. The steel hopper holds approximately 10 bushels and has an easy-to-use axle locking mechanism. Two heavy-duty, 16″ diameter tires navigate easily through rugged terrain. MAJOR COMPONENTS Hopper Spreading Drum...
- Page 5 SAFETY SAFETY GUIDELINES ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED! Safety is a primary concern in the design and manufacture of our products. Unfortunately, our efforts to provide safe equipment can be wiped out by an operator’s single careless act. In addition to the design and configuration of equipment, hazard control and accident prevention are dependent upon the awareness, concern, judgment, and proper training of personnel involved in the operation, transport, maintenance and storage of equipment.
- Page 6 Never exceed the limits of any piece of machinery, sources close to the ear) is cumulative over a lifetime whether the power unit or the Tarter implement. If its without hope of natural recovery. ability to perform a job safely is in questions, DO NOT TRY IT.
- Page 7 SAFETY OPERATION Never operate the power unit or the Tarter implement while under the influence of alcohol or drugs. The use of this equipment is subject to certain hazards that cannot be protected against by mechanical TRANSPORT means or product design. Before using this...
- Page 8 SAFETY MAINTENANCE Always use personal protective devices, such as eye, hand, and hearing protectors, when performing any Follow good maintenance practices. Understand and service or maintenance. Wear a respirator or filter adhere to all maintenance procedures outlined in this mask when appropriate. manual.
-
Page 9: Safety & Instruction Decals
SAFETY & INSTRUCTION DECALS ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED! Replace Decals Immediately if Damaged! PINCH POINT MANUAL NOTICE (decal located inside hopper) CRUSH POINT GREASE WARNING ENGAGE WHEEL GREASE CAUTION Warning Label Sheet Part Number 4000008... -
Page 10: Attaching
ATTACHING / OPERATION ATTACHING OPERATION 1. Fill the spreader with manure. 1. First, make sure you are on a level surface. Back ATV/UTV up to the tongue of the spreader. Align the ATV/UTV hitch to the holes on the tongue of the spreader. -
Page 11: Detaching
DETACHING / MAINTENANCE / STORAGE DETACHING STORAGE 1. Put the ATV/UTV in PARK and set the parking 1. Clean any manure and debris from the spreading brake. drum and hopper before storing the spreader. 2. Disengage the Axle Locking Lever to prevent the 2. -
Page 12: Specifications
SPECIFICATIONS / TROUBLESHOOTING SPECIFICATIONS MODEL MS1002 Dimensions Width, in. (cm) 49 (124.46) Height, in. (cm) 28 (71.12) Length, in. (cm) 76 (193.04) Capacity 12 cubic ft., approximately 10 bushels Weight Implement, lb (kg) 207 (93.89) Construction Frame and Hopper 1-1/2″ sq. x 3/16″ steel tube frame and 1/8″ steel hopper... - Page 13 PARTS MS1002 Item# Service Number Description 2000116 Agitator Bar 2000117 Tire/Wheel Combo 9000021 Axle Locking Mechanism w/ Hardware 2000118 Rubber Seal Strip 9000022 Handle w/ Hardware 2000119 Large Agitator Sprocket 2000120 Small Axle Sprocket 2000121 Chainguard 2000122 Agitator Block Bearing...
- Page 14 TORQUE SPECIFICATIONS Proper torque for American fasteners used on manufactured implement. AMERICAN Recommended Torque in Foot Pounds (Newton Meters).* Bolt Head Markings WRENCH BOLT DIAMETER SIZE(IN.) “A” (IN.) “B” AND GRADE 2 GRADE 5 GRADE 8 THREAD SIZE 7/16 1/4 -20 UNC 6 (7) 8 (11) 12 (16)
- Page 15 TORQUE SPECIFICATIONS Proper torque for metric fasteners used on manufacturer implement. METRIC Recommended Torque in Foot Pounds (Newton Meters).* WRENCH SIZE BOLT DIA. ASTM ASTM ASTM ASTM (mm) “A” (mm) “B” 10.9 1.8 (2.4) 5.1 (6.9) 6.5 (8.8) 3 (4) 8.7 (12) 11.1 (15) Wrench...
-
Page 16: Warranty
3. Photograph of UPC label. After receipt of the above information, if the product is alleged to be defective, Tarter Farm and Ranch Equipment will process the claim and issue a Return Manufacturers Authorization number (RMA). Once an RMA number is issued, Tarter Farm and Ranch Equipment will pick up the product from the authorized retailer and return to its facility for inspection. - Page 17 The choice of remedy shall belong solely to Tarter Farm and Ranch Equipment. In no event shall Tarter Farm and Ranch Equipment be liable for any loss or damages of any other kind, whether direct, incidental, consequential including lost profits, exemplary, special, or otherwise, including without limitation, expenses incurred for substitute or replacement implement or for rental expenses to temporarily replace a warranted product.
- Page 18 NOTES...
- Page 19 NOTES...
- Page 20 P.O. BOX 10 10739 S. HWY 127 DUNNVILLE, KY 42528 1-800-RED-GATE | TARTERUSA.COM 4000007 REV 4...