Related Manuals for Draytek 35b Series
Summary of Contents for Draytek 35b Series
- Page 1 Vigor2765 35b Series Router Quick Start Guide Version: 1.8 Firmware Version: V4.4.3.2 (For future update, please visit DrayTek web site) Date: April 12, 2024...
- Page 2 Intellectual Property Rights (IPR) Information © All rights reserved. This publication contains information that is protected Copyrights by copyright. No part may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language without written permission from the copyright holders. The following trademarks are used in this document: Trademarks Microsoft is a registered trademark of Microsoft Corp.
- Page 3 EU Declaration of Conformity Hereby, DrayTek Corporation declares that the equipment type Vigor2765 is in compliance with EU EMC Directive 2014/30/EU, Low Voltage Directive 2014/35/EU and RoHS 2011/65/EU. The full text of the EU declaration of conformity is available at the following internet address: https://fw.draytek.com.tw/Vigor2765/Document/CE/...
- Page 4 81.3% 83.3% 83.7% 74.5% 80.5% 86.4% 85.4% 85.4% 84.7% 87.7% low load 10% No-load power 0.07W 0.07W 0.07W 0.07W 0.07W 0.07W 0.10W 0.07W 0.10W 0.10W 0.08W 0.10W consumption External power supply (Power Adapter) information. For more update, please visit www.draytek.com.
-
Page 5: Table Of Contents
1. Package Content ....................1 2. Panel Explanation....................2 3. Hardware Installation ................... 4 3.1 Network Connection ........................4 3.2 Wall-Mounted Installation ......................5 4. Software Configuration ..................6 5. Customer Service ....................11 Be a Registered Owner ........................11 Firmware & Tools Updates ......................11... -
Page 6: Package Content
Take a look at the package content. If there is anything missed or damaged, please contact DrayTek or dealer immediately. Vigor router Quick Start Guide RJ-45 Cable (Ethernet) RJ-11 to RJ-11 Cable (Annex A) RJ-11 to RJ-45 Cable (Annex B) -
Page 7: Panel Explanation
Status Explanation Blinking The router is powered on and running normally. The router is powered off. (Activity) The DSL link up, waiting for the Internet connection. Orange Slowly - The DSL connection is ready for training. Blinking (DSL) Quickly - The DSL connection is synchronizing. The router is ready to access to the Internet through DSL link. - Page 8 Interface Description Factory Reset Restore the default settings. Usage: Turn on the router (ACT LED is blinking). Press the hole and keep for more than 5 seconds. When you see the ACT LED begins to blink rapidly than usual, release the button. Then the router will restart with the factory default configuration.
-
Page 9: Hardware Installation
This section will guide you to install the router through hardware connection and configure the router’s settings through web browser. Before starting to configure the router, you have to connect your devices correctly. Connect the DSL interface to the land line jack with a DSL line cable. Connect one port of 4-port switch to your computer with a RJ-45 cable. -
Page 10: Wall-Mounted Installation
Vigor router has keyhole type mounting slots on the underside. Drill two holes on the wall. The distance between the holes shall be 168mm. Fit screws into the wall using the appropriate type of wall plug. With the screws installed, the router can be slotted into place. Note The recommended drill diameter shall be 6.5mm (1/4”). -
Page 11: Software Configuration
To access Internet, please finish basic configuration after completing the hardware installation. Here we take Vigor2765 as an example. The Quick Start Wizard is designed for you to easily set up your router for Internet access. You can directly access the Quick Start Wizard via Web Configurator. - Page 12 Now, the Main Screen will pop up. Click Wizards>>Quick Start Wizard. Note The home page will change slightly in accordance with the router you have. The first screen of Quick Start Wizard is entering login password. After typing the password, please click Next.
- Page 13 On the next page as shown below, please select the WAN interface that you use. If DSL interface is used, please choose WAN1; if Ethernet interface is used, please choose WAN2; if 3G USB modem is used, please choose WAN3. Then click Next for next step.
- Page 14 After finished the above settings, simply click Next. Please manually enter the Username/Password provided by your ISP. Then click Next for viewing summary of such connection. Click Finish. A page of Quick Start Wizard Setup OK!!! will appear. Then, the system status of this protocol will be shown. Now, you can enjoy surfing on the Internet.
- Page 15 Choose WAN1 as WAN Interface and click the Next button; you will get the following page. Please type in the IP address/mask/gateway information originally provided by your ISP. Then click Next for viewing summary of such connection. Click Finish. A page of Quick Start Wizard Setup OK!!! will appear. Then, the system status of this protocol will be shown.
-
Page 16: Customer Service
If the router cannot work correctly after trying many efforts, please contact your dealer/DrayTek for further help right away. For any questions, please feel free to send e-mail to “support@draytek.com”. Web registration is preferred. You can register your Vigor router via https://myvigor.draytek.com.
Need help?
Do you have a question about the 35b Series and is the answer not in the manual?
Questions and answers