Related Manuals for Enttec 71030
Summary of Contents for Enttec 71030
- Page 1 DIN ETHERGATE 71030 User Manual Two-Universe bi-directional eDMX - DMX/RDM gateway in a compact 4-module DIN-rail form factor.
-
Page 2: Table Of Contents
DIN ETHERGATE (71030) ENTTEC website Visit the for the latest version. Content Safety............................................. 3 Electrical safety ............................................. 3 System Planning and Specification .................................... 3 Protection from Injury During Installation ................................4 Installation Safety Guidelines ....................................... 4 Physical Dimensions ...................................... 5 Mounting Options ...................................... -
Page 3: Safety
ENTTEC device. If you are in any doubt about system safety, or you plan to install ENTTEC device in a configuration that is not covered within this guide, contact ENTTEC or your ENTTEC supplier for assistance. -
Page 4: Protection From Injury During Installation
All network cabling should be terminated with an RJ45 connector in accordance with the T-568B standard. Always use suitable personal protective equipment when installing ENTTEC products. Once installation is completed, check that all hardware and components are securely in place and ... -
Page 5: Physical Dimensions
DIN ETHERGATE (71030) ENTTEC website Visit the for the latest version. Physical Dimensions Mounting Options USER MANUAL Document Updated: April 2023 ID: 5928465 ... -
Page 6: Wiring Diagrams
The maximum cable distance DMX can be run without re-buffering is 300m (ft 984ft). Never exceed 32 devices in a DMX chain without an intermediary DMX splitter or buffer (i.e. ENTTEC’s DIN RDS4). Terminate all DMX chains with a DMX terminator to eliminate signal bounce back. When using the ... - Page 7 DIN ETHERGATE (71030) ENTTEC website Visit the for the latest version. DMX FROM LIGHTING CONTROLLER POWER OVER ETHERNET (PoE) DMX FROM LIGHTING CONTROLLER DMX FROM LIGHTING CONTROLLER POWER OVER ETHERNET (PoE) DMX TO LIGHTING FIXTURES DMX FROM LIGHTING CONTROLLER DMX TO LIGHTING FIXTURES...
-
Page 8: Functional Features
▪ The device functions as a gateway and does not support remote configuration through Art-Net. ▪ ENTTEC advises disabling RDM when not needed for your fixtures. Older fixtures compatible with the DMX 1990 Specification may exhibit erratic behavior with RDM packets present on the DMX line. -
Page 9: Merging
DIN ETHERGATE (71030) ENTTEC website Visit the for the latest version. Merging Merging is available when the DIN ETHERGATE ‘Type’ is set to Output (DMX Out). Two different Ethernet- DMX sources (from different IP addresses) values can be merged if the source is the same protocol and universe. -
Page 10: Led Status Indicator
DIN ETHERGATE (71030) ENTTEC website Visit the for the latest version. LED Status Indicator The DIN ETHERGATE comes with a forward facing RGB LED indicator. The LED signifies the related activity: LED Colour Status Description Idle White Indicates normal operation of the DIN ETHERGATE. -
Page 11: Networking
Note: When configuring multiple DIN ETHERGATE’s on a Static network; to avoid IP conflicts, ENTTEC recommends connecting one device at a time to the network and configuring an IP. If using DHCP as your IP addressing method, ENTTEC recommends the use of the sACN multicast, or ... -
Page 12: Home
DIN ETHERGATE (71030) ENTTEC website Visit the for the latest version. Home The landing page for the DIN ETHERGATE web interface is the Home tab. This tab is designed to give you a read-only device overview. This will display: System Information: Node Name ... -
Page 13: Network Stats
DIN ETHERGATE (71030) ENTTEC website Visit the for the latest version. Type: Choose from the following options: Disabled Input (DMX IN) Output (DMX Out) Protocol: Choose between Art-Net, sACN and ESP as the Protocol. RDM: RDM (ANSI E1.20) can be selected using the tick box. -
Page 14: Update Firmware
Firmware Version, Mac Address and IP address information. The latest firmware can be downloaded from www.enttec.com. Use the Browse button to access in your local computer for the latest DIN ETHERGATE firmware file which has a .bin extension. - Page 15 DIN ETHERGATE (71030) ENTTEC website Visit the for the latest version. 3. Launch the EMU Software on your computer and select from the DIN ETHERGATE discovered. The EMU Software will prompt you to access the boot page for firmware updates or other maintenance tasks.
-
Page 16: Servicing, Inspection & Maintenance
Do not spray device or accessories. The device is an IP20 product. To clean an ENTTEC device, use low-pressure compressed air to remove dust, dirt and loose particles. If deemed necessary, wipe the device with a damp microfiber cloth. -
Page 17: Package Contents
Boot version V2.1 ▪ Firmware version V2.1 ▪ Ordering Information For further support and to browse ENTTEC’s range of products visit the ENTTEC website. Item Part No. DIN ETHERGATE 71030 Due to constant innovation, information within this document is subject to change.
Need help?
Do you have a question about the 71030 and is the answer not in the manual?
Questions and answers