Advertisement
To remove the skid plate:
1. Remove the battery pack.
2. Unclasp the clevis hook form the clevis pin. Re-
move the clevis pin from the skid plate.
3. Push the front side of the skid plate away from
the front blade block pin to remove the skid plate
from the machine.
Installing/Removing the Blade
Examine the blade for damage or
WARNING
wear. If the blade shows damage
or wear, discard the blade. A worn or damaged
blade can cause injury.
Replace the blade when it becomes dull or chipped.
A blade is dull when the blade edge appears rounded
or damaged.
To install the blade:
1. Remove the battery pack.
2. Push the handlebar down to set the machine in
the tilt position.
3. Loosen the blade block knob. Once loosened,
rotate the blade block upwards.
4. Remove the clevis pin to loosen the skid plate.
Remove skid plate from the machine.
5. Hold down the spindle lock button. Using the
wrench provided, loosen the blade shaft bolt.
Spindle
lock button
Blade
block knob
Blade
Blade shaft
Outer flange
Inner flange
bolt
6. Remove the blade shaft bolt and outer flange.
7. Place the blade tightly against the inner flange.
Make sure the rotation direction of the blade is
correct.
NOTE: The direction of the blade can be found on
the decal above the blade block.
8. Place the outer flange tightly against the blade.
9. Place the blade shaft bolt through the outer flange,
blade, and inner flange. Hold down the spindle
lock button and tighten the bolt clockwise with a
wrench.
10. Reinstall the skid plate using the clevis pin.
11. Rotate the blade block back down. Tighten the
blade block knob to resecure the blade block.
To remove the blade:
Blade may be HOT. Allow to cool
CAUTION
before contacting.
1. Remove the battery pack.
2. Push the handlebar down to set the machine in
the tilt position.
3. Loosen the blade block knob. Once loosened,
rotate the blade block upwards.
4. Remove the clevis pin to loosen the skid plate.
Remove skid plate from the machine.
5. Hold down the spindle lock button. Using the
wrench provided, loosen the blade shaft bolt.
6. Remove the blade shaft bolt and outer flange, then
remove the blade from the blade shaft.
Folding/Unfolding the Handle
Pinch hazard. Keep body parts away
CAUTION
from hinges during folding and
unfolding of the handle.
To fold the handle down:
1. Press the button at the top of the locking pins and
pull the locking pins out of the handle.
2. Fold the handle down, towards the roll cage.
3. Hold the button at the top of the locking pins and
push the pins back into the handle.
To unfold the hande:
1. Press the button at the top of the locking pins and
pull the locking pins out of the handle.
2. Unfold the handle, pulling it up and away from the
base of the machine.
3. Hold the button at the top of the locking pins and
Blade
push the pins back into the handle.
block
Adjusting Handle Height
The handle can be adjusted to one of two heights in
the unfolded position. To adjust the handle height,
pull and hold the two adjustment levers in towards
each other, then push the handle up or down to the
desired position. Release the adjustment levers and
make sure they are pinned securely into one of the
two height adjustment latches.
Height
adjustment
levers
Height adjustment latches
Handle
6
Hoisting with a Device
Do not lift with forks. Do not lift with
WARNING
an excavator bucket. Only hoist
machine with lifting gear rated for the application.
Remove the battery pack and fold the handle down.
To hoist the machine, use the lift plate as the anchor
point. Ensure the hoisting strap will not slip or contact
other parts.
Lifting with Roll Cage
Use multiple people when-
WARNING
ever it is necessary to lift or
carry the machine. Machine is heavy. Lift
with legs, not back.
Always remove the battery pack from the ma-
chine before transporting.
Always fold the handle before transporting.
Always clear the area of obstructions before
transporting.
To lift, use the roll cage on each side of the machine
and lift with two hands. Always maintain a firm footing.
NOTE: Attach the skid plate to prevent damage to
the front and rear shaft while transporting.
Transporting
All displacement of the machine
WARNING
outside the cutting area shall be
carried out with the tool not in rotation.
To roll the machine from place to place, grasp the
handle and tilt the machine back onto the wheels.
Push, don't pull, the machine.
Transporting
position
Transporting with a Vehicle
Remove the battery pack and fold the handle down.
Strap the machine down to secure it to the vehicle.
The straps should be placed through the roll cage,
either front to back of the machine and/or side to
side of the machine.
ONE-KEY™
To learn more about the ONE-KEY™ functionality for
this machine, go to milwaukeetool.com/One-Key. To
download the ONE-KEY™ app, visit the App Store
or Google Play™ from your smart device.
ONE-KEY™ Indicator
Solid Blue
Wireless mode is active and ready
to be configured via the ONE-KEY™
app.
Blinking Blue Machine is actively communicating
with the ONE-KEY™ app.
Blinking Red Machine is in security lockout and
can be unlocked by the owner via
the ONE-KEY™ app.
OPERATION
To reduce the risk of injury, always
WARNING
wear proper eye protection marked
to comply with ANSI Z87.1.
When working in dusty situations, wear appro-
priate respiratory protection or use an OSHA
compliant dust extraction solution.
For Use with the Dust Extractor
Use the dust extractor connection to plug a dust ex-
tractor to the machine. For dust extractor assembly
and operation, refer to your dust extractor manual.
Keep the dust extractor connection closed when not
using a dust extractor.
Dust
extractor
Dust
extractor
connection
Setting the Blade Depth Adjustment
Before setting the blade depth adjustment, put the
machine in transporting position.
To set the blade depth adjustment, pull the blade
depth adjustment knob away from the machine and
move it to the desired setting.
Arming the Machine
The MX FUEL™ machines must be armed prior to
use. Even with the battery pack inserted, the trig-
ger and machine functions will not operate until the
machine is armed.
To arm the machine:
1. Insert the battery pack.
®
2. Press the Arm button. The MX FUEL™ icon will
light. The trigger will become armed in 2 seconds.
3. After 15 minutes of inactivity, the machine will enter
sleep mode. The MX FUEL™ icon will go off and
the trigger and LEDs are un-operational.
4. Press and hold the Arm button for 1 second to
reactivate the machine.
5. Press and hold the ARM button for 1 second to
unarm (turn off) the machine. The MX FUEL™
icon will go off.
NOTE: The machine can be armed while the power
switch is in the on position. However, the machine
cannot be operated until the power switch is flipped
off and back on again.
7
Advertisement
