Related Manuals for Worx Nitro WG737E Series
Summary of Contents for Worx Nitro WG737E Series
- Page 1 SAFETY AND OPERATING MANUAL ORIGINAL INSTRUCTIONS Cordless Brushless Push Lawn Mower WG737E WG737E.X...
- Page 5 100%...
- Page 6 1——20 mm 2——30 mm 3——40 mm 4——50 mm 5——60 mm 6——70 mm 100%...
-
Page 8: Table Of Contents
TABLE OF CONTENT increase the risk of electric shock. d) Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the power tool. 1. SAFETY INSTRUCTIONS Keep cord away from heat, oil, sharp edges 2. COMPONENT LIST or moving parts. - Page 9 f) Do not expose a battery pack or tool to fire turn it on and off. Any power tool that cannot be or excessive temperature. Exposure to fire or controlled with the switch is dangerous and must be repaired. temperature above 130 °C may cause explosion. c) Disconnect the plug from the power source and/ g) Follow all charging instructions and do not charge or remove the battery pack, if detachable, from...
- Page 10 falling which may result in personal injury. be necessary to charge and discharge the k) Do not operate the lawnmower on excessively battery pack several times to obtain maximum steep slopes. This reduces the risk of loss of performance. k) Recharge only with the charger specified control, slipping and falling which may result in personal injury.
-
Page 11: Component List
FRONT CARRY HANDLE BATTERY PACK COVER Do not burn REAR CARRY HANDLE HANDLE KNOB, LOWER Li-Ion battery This product has LOWER HANDLE been marked with a symbol CABLE CLIP relating to ‘separate collection’ for all battery packs and battery HANDLE KNOB, UPPER pack. -
Page 12: Intended Use
The tool being in good condition and well maintained. Machine Weight Using the correct accessory for the tool and ensuring it 14.0 kg (bare tool) is sharp and in good condition. The tightness of the grip on the handles and if any anti ** X=1-999,A-Z,M1-M9 they are only used for different vibration accessories are used. - Page 13 Adjusting the cutting height Fitting grass collection bag to the See Fig. See Fig. G mower. C1,C2 WARNING! Stop, release NOTE: Depress the grass switch lever and wait until the motor stops before adjusting collection bag slightly to ensure that it is completely installed. height.
-
Page 14: Maintenance
CUTTING AREA The battery level of at least Only one green one battery pack is very low. light ( ) is The cutting area can be affected by several factors, Please check and charge the illuminated. such as cutting height, lawn humidity, grass length battery pack. - Page 15 ENVIRONMENTAL KEEP BLADE SHARP FOR BEST MOWER PERFORMANCE. PROTECTION WEAR PROPER EYE PROTECTION WHILE REMOVING, SHARPENING, AND INSTALLING BLADE. Waste electrical products must not be disposed Sharpening the blade twice during a mowing season is of with household waste. Please recycle where usually sufficient under normal circumstances.
-
Page 16: Troubleshooting
7. TROUBLESHOOTING Problem Solution 1. Mower doesn’t run when A. Check to make sure the button on switch housing is being completely switch lever is activated. pushed. B. Release Switch Lever to turn mower off. Turn mower over and check that blade is free to turn. - Page 17 11. The battery charger LED A. The battery overheats after continuous use. Remove battery from the flashes red and the battery charger and allow it to cool to 42 C or less. can’t be charged. 8. DECLARATION OF CONFORMITY Positec Germany GmbH Postfach 32 02 16, 50796 Cologne, Germany On behalf of Positec declare that the product Description Cordless Lawn Mower...
-
Page 18: Declaration Of Conformity
DECLARATION OF CONFORMITY Positec (UK & Ireland) Ltd, PO Box 6242, Newbury, RG14 9LT, UK On behalf of Positec declare that the product Cordless Lawn Mower Description Type WG737E WG737E.X (7- designation of machinery, representative of Cordless Lawn Mower) Function mowing grass Complies with the following regulations: Supply of Machinery (Safety) Regulations 2008 Electromagnetic Compatibility Regulations 2016... - Page 20 www.worx.com Copyright © 2023 Positec. All Rights Reserved. V1-UK-WG737E WG737E.X-M-20231024...
Need help?
Do you have a question about the WG737E Series and is the answer not in the manual?
Questions and answers
I just assembled my new WORX NITRO WG737 lawn mower. The handlebar is somewhat loose. I feel it should be tighter. The handle levers are tight. Please advise. Thanks
To tighten the handlebar on your Worx Nitro WG737 lawn mower, follow these steps:
1. Assemble the handlebar by aligning the upper and lower handle sections as shown in Figures A1 to A4.
2. Choose the appropriate handle height.
3. Tighten the handle using the handle knobs provided.
Make sure the handle is secure before operating the mower.
This answer is automatically generated