Sealey BJ20LE Manual

Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these
instructions, and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
Refer to Wear safety
instructions footwear
1. SAFETY
WARNING! ALWAYS USE LOAD RATED STANDS TO SUPPORT LIFTED LOADS
‰
Read, study and understand all warnings and operating instructions prior to use. The user shall work in accordance with this manual.
9
▲ DANGER! Use the jack for lifting and lowering only.
▲ DANGER! DO NOT place any part of the body beneath the lifted load unless the load is fully supported by rated axle stands.
▲ DANGER! DO NOT place any part of the body beneath the load during lifting or lowering.
DO NOT exceed the rated capacity of the jack, load or maximum stroke.
8
DO NOT adjust the overload valve, modify or use the jack for any purpose other than for which it is designed (lifting and lowering
8
mechanical devices).
DO NOT leave elevated loads unattended, unless safe from others in a garage or workshop.
8
DO NOT modify the jack.
8
The operator must watch the jack and the load during all movements.
9
Ensure the jacking area is solid and level. Increase the jacking area with a solid flat plate (steel) if jacking on tarmacadam or grass.
9
Keep others away from the work area.
9
Lift only on areas of the vehicle specified by the vehicle manufacturer. Refer to manufacturer's instructions on proper lifting.
9
Centre load on saddle prior to lifting.
9
Some vehicles require an adapter to properly engage the frame for lifting.
9
Use only attachments, restraints or adaptors supplied by the manufacturer.
9
DO NOT move or dolly the the vehicle whilst on the jack.
8
Ensure the jacking area is clutter free and that there is adequate lighting.
9
WARNING! Remember, it is very dangerous to go under a vehicle supported by a jack even if additional supports are used.
‰
DO NOT go under a vehicle unless it is supported by adequately rated axle stands. NOTE: Seek advice before jacking caravans or
8
trailers.
WARNING! The warnings, cautions and instructions in this manual cannot cover all possible conditions and situations
‰
that may occur. It must be understood by the operator that common sense and caution are factors which cannot
be built into this product, but must be applied by the operator.
WARNING! Failure to heed these warnings may result in personal injury and/or property damage.
8
2. INTRODUCTION
Fitted with overload valve. Base and reservoir machine welded for increased strength and reduced chance of leakage. Threaded
pump assembly allows for easy disassembly and maintenance. Supplied with 4-piece operating handle. Fitted with carrying handle.
Service kit readily available.
3. SPECIFICATION
Model No: ..........................................................BJ20LE
Capacity: .......................................................... 20tonne
Minimum Height: ............................................... 155mm
Maximum Height: .............................................. 250mm
Hydraulic Lift: ...................................................... 95mm
Screw Extension: .................................................... N/A
4. OPERATION
IMPORTANT SAFETY WARNING: ALWAYS USE AXLE STANDS
Please remember a jack is a lifting and lowering device and is not designed to support a load. Never get underneath a
vehicle supported only by a jack; your life is at risk. We stock a comprehensive range of axle stands, please see relevant
catalogue section for full details.
The jack is not limited to vehicle use only, with many applications in the engineering and construction industries.
4.1. The owner and/or operator is responsible for providing maintenance, maintaining decals or warning labels whilst in use,
Maintaining the unit in good working order. If the owner and/or operator is not fluent in English, the product warnings
and instructions shall be read in the operator's native language by the purchaser/owner or his deputy.
Make sure operator understands its contents. Safety information shall be emphasised and understood prior to usage. The jack shall
be inspected as per the instruction manual prior to use.
© Jack Sealey Limited
20 TONNE TELESCOPIC LOW PROFILE BOTTLE
JACK
MODEL NO:
Beware crushing Wear eye
hands protection
Original Language Version
BJ20LE
Wear protective
gloves
BJ20LE Issue: 3(3) 01/11/23