Sealey BJ10LE Manual

Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these
instructions, and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
Refer to
instructions
1. SAFETY
9 I nspect and lubricate the jack regularly to ensure it is in good working order. DO NOT use the jack if damaged or a fault is suspected.
9
9
Check chapter 6 troubleshooting. If necessary, repair or replace damaged parts immediately.
9 U se authorised parts only, the use of unauthorised parts may be dangerous and will invalidate your warranty.
9
9
9 E nsure the jacking area is clean and tidy and free from unrelated materials and there is adequate lighting.
9
9
9 U se jack on level and solid ground, preferably concrete. Avoid tarmacadam since the jack may sink in.
9
9
9 P ark the vehicle and apply hand brake; if automatic, place in Park (P) mode. Switch off the engine, and place chocks under the wheels.
9
9
9 E nsure minimum distance of 0.5m between vehicle tilt and static objects such as doors, walls, etc.
9
9
9 E nsure all persons are out of the vehicle before jacking. DO NOT enter vehicle whilst it is supported on the jack or axle stands.
9
9
9 C heck vehicle weight and recommended lifting points by referring to the vehicle owner's manual. Ensure the lifting point is not corroded.
9
9
9 C heck jack saddle is centred and stable on lifting point, (off-centre loads can slip). Position jack to avoid operating it from under vehicle.
9
9
▲ 9 D ANGER! Use the jack for lifting only, NOT for supporting the lifted load. ALWAYS USE PROPERLY RATED AXLE STANDS.
9
9 K eep hands etc. clear of moving parts during raising and lowering of the vehicle.
9
9
9 U se properly rated axle stands under the vehicle before proceeding with any task.
9
9
▲ 9 D ANGER! Roadside wheel change is hazardous. Be extra vigilant. You may not be able to avoid jacking on tarmacadam. Get everyone
9
out of vehicle. NEVER go under vehicle, traffic may cause vehicle to rock. Use hazard warning lights. If in doubt call professional help.
9 W hen changing a wheel, slightly loosen wheel nuts prior to jacking vehicle. Screw wheel nuts back before lowering vehicle.
9
9
9 U se a competent person to lubricate and maintain the jack.
9
9
9 D O NOT exceed the rated capacity of the jack, and9DO NOT operate the jack beyond its maximum pump stroke.
9 8
9 W ARNING! DO NOT allow the vehicle to move during jacking. DO NOT start the engine when vehicle is jacked up.
‰
9
9 D O NOT jack a vehicle if it may result in the spillage of fuel, battery acid, or other dangerous substances.
9 8
9 D O NOT place any part of your body under vehicle whilst supported by jack. Wait until properly rated axle stands have been correctly
9 8
positioned.
9 D O NOT use jack to support extensions or cradles. DO NOT modify jack in any way. DO NOT use the jack for any other purpose than
9 8
that for which it is designed.
9 D O NOT top up jack hydraulic system with brake fluid. Use hydraulic oil only, and DO NOT adjust the safety overload valve.
9 8
9 E nsure there are no persons or obstruction beneath the vehicle before lowering.
9
9
9 C lean, and stow the jack securely, with the ram in the down position. Ensure stowage area is dry.
9
9
9 W ARNING! Remember, It is very dangerous to get under a vehicle supported by a jack even if additional supports are used.
‰
9
DO NOT go under a vehicle without the support of properly rated axle stands. NOTE: Seek advice before jacking caravans or trailers.
8
2. INTRODUCTION
Fitted with overload valve. Base and reservoir machine welded
for increased strength and reduced chance of leakage. Threaded
pump assembly allows for easy disassembly and maintenance.
Supplied with 4pc handle. Fitted with carrying handle. Service kit
readily available.
IMPORTANT SAFETY WARNING: ALWAYS USE AXLE STANDS
Please remember a jack is a lifting device and is not designed to
support a load. Never get underneath a vehicle supported only
by a jack - your life is at risk. We stock a comprehensive range of
axle stands - please see relative section for full details.
3. SPECIFICATION
Model No: . . . . . . . . . . . . . . . . . . . . . . . . . . . BJ10LE
Capacity:. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10Tonne
Minimum Height:. . . . . . . . . . . . . . . . . . . . . . . .128mm
Maximum Height: . . . . . . . . . . . . . . . . . . . . . . .223mm
Hydraulic Lift: . . . . . . . . . . . . . . . . . . . . . . . . . . .95mm
Screw Extension: . . . . . . . . . . . . . . . . . . . . . . . . . . N/A
© Jack Sealey Limited
BOTTLE JACK
10TONNE LOW ENTRY TELESCOPIC
BJ10LE
MODEL NO:
Original Language Version BJ10LE Issue: 2 (H,F, 2) - 10/06/19