Related Manuals for Clarke CI350
Summary of Contents for Clarke CI350
- Page 1 350W POWER INVERTER MODEL NO: CI350 PART NO: 6013031 USER INSTRUCTIONS ORIGINAL INSTRUCTIONS DL06/23...
-
Page 2: Safety Symbols
Overload, Over temperature and Output short circuit. These five functions can protect the electrical equipment and the circuit of the vehicle. This CLARKE product has been designed to give long and trouble free service. If, however, having followed the instructions in this booklet carefully, you encounter problems, take the unit to your local CLARKE dealer. -
Page 3: General Safety Precautions
4. Keep out of the reach of children. 5. ALWAYS have the unit repaired by your local CLARKE dealer, using only identical replacement parts. This will ensure the safety of the unit is maintained. The use of non standard parts could be hazardous. -
Page 4: Product Specifications
5-35 NOTE: The details and specifications contained herein, are correct at the time of going to print. However, CLARKE International reserve the right to change specifications at any time without prior notice. Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com... -
Page 5: Product Features
PRODUCT FEATURES DC Input Positive + Terminal (Red) AC 230V Output Socket DC Input Negative - Terminal (Black) On/Off Switch Cooling Fan (Thermally Controlled) USB Port 40A External Fuse Positive + (Red) Connection Cable Power LED Light (Green) Negative - (Black) Connection Cable Fault LED Light (Red) Parts &... -
Page 6: General Operation
GENERAL OPERATION CONTROLS, INDICATORS AND CONNECTORS An ON/OFF switch turns the inverter on and off and will reset the inverter internal circuits. One end panel provides DC connections for battery clamps and a 40A fuse. A 230V AC 3 pin plug socket and a USB connector is provided on the other end together with two LEDs (green and red) and the On/Off switch. - Page 7 CONNECTION AND POSITIONING Connecting the inverter in the wrong way may damage the inverter as well as the electrical equipment. Please follow the steps below to avoid connection errors. CONNECTING TO A BATTERY 1. Insert the ring terminal end of the Positive (Red, +) connection cable into the DC input Positive (Red, +) terminal on the inverter and tighten the holding screw.
- Page 8 CAUTION: THE INVERTER MUST BE CONNECTED ONLY TO BATTERIES WITH A NOMINAL OUTPUT VOLTAGE OF 12-VOLTS. THE UNIT WILL NOT OPERATE FROM A 6-VOLT BATTERY AND WILL SUSTAIN DAMAGE IF CONNECTED TO A 15-VOLT BATTERY OR HIGHER. MAKE SURE THAT THE BATTERY’S VOLTAGE NEVER EXCEEDS 15-VOLTS, AS THIS WILL INVALIDATE THE WARRANTY.
- Page 9 To avoid excessively discharging the vehicle battery, it is advisable to let your engine run for a while after a period of using the inverter. This allows the vehicle battery to recharge. Always remember to disconnect the AC inverter before using a battery charger to recharge your battery.
-
Page 10: System Protection
SYSTEM PROTECTION The inverter has; • input low voltage protection, • input over voltage protection • over load protection, • over temperature protection and • short circuit protection. If these are activated the inverter will shut down. After troubleshooting, the inverter will work normally again. The inverter will switch off automatically if the total wattage of the connected appliance(s) exceeds the inverter output capacity. - Page 11 After fuse replacement, reconnect the inverter and if a fuse continues to blow, contact your CLARKE dealer or telephone CLARKE International on 020 8998 7400. DO NOT open the unit as there are no user serviceable parts inside.
-
Page 12: Troubleshooting
TROUBLESHOOTING Protection Condition Re-start method LED light Alarm output Input low voltage Green Alarm When the battery voltage alarm on/red off returns to the related volt- age, alarm stops auto- matically. Input Low-Voltage Green on Alarm When the battery voltage shut down Red on returns to the related volt-... -
Page 13: Care And Maintenance
GUARANTEE This CLARKE product is guaranteed against faulty manufacture for a period of 12 months from the date of purchase. Please keep your receipt as proof of purchase. - Page 14 DECLARATION OF CONFORMITY -UK Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com...
-
Page 15: Declaration Of Conformity (Ce)
DECLARATION OF CONFORMITY - CE Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com...
Need help?
Do you have a question about the CI350 and is the answer not in the manual?
Questions and answers