Table of Contents
Advertisement
•
The operation of the thermal cut-out indicates a possibly dangerous situation. Do not reset the thermal cut-out until
the water heater has been serviced by a qualified person.
•
Failure to operate the relief valve easing gear at least once every six months may result in the water heater
exploding. Continuous leakage of water from the valve may indicate a problem with the water heater.
•
If the hot water system is not used for two weeks or more, a quantity of highly flammable hydrogen gas may
accumulate in the water heater. To dissipate this gas safely, it is recommended that a hot tap be turned on for
several minutes or until discharge of gas ceases. Use a sink, basin, or bath outlet, but not a dishwasher, clothes
washer, or other appliance. During this procedure, there must be no smoking, open flame, or any electrical
appliance operating nearby. If hydrogen is discharged through the tap, it will probably make an unusual sound
as with air escaping.
•
Before touching electric terminal parts, turn off power switch.
•
Do not touch the inner parts of the controller.Do not remove the front panel. Some parts inside are dangerous to
touch, otherwise a machine malfunction may be caused.
•
When front panels are removed, live parts can be easily touched by accident.
•
Never leave the unit unattended during installation or servicing when the front panel is removed.
•
Do not touch water pipes during and immediately after operation as the pipes may be hot and could burn your
hands. To avoid injury, give the piping time to return to normal temperature or be sure to wear protective gloves.
•
Do not touch any switch with wet fingers. Touching a switch with wet fingers can cause electrical shock.
•
Before touching electrical parts, turn off all applicable power to the unit.
•
If the water supply pressure exceeds the rated pressure, a pressure reducing valve is to be fitted in the installation.
•
The water may drip from the discharge pipe of the pressure-relief device and that this pipe must be left open to the
atmosphere.
•
The pressure-relief device is to be operated regularly to remove lime deposits and to verify that it is not blocked.
•
A discharge pipe connected to the pressure-relief device is to be installed in a continuously downward direction and
in a frost-free environment.
•
For appliances with supplementary heaters, the minimum clearance from the appliance to combustible surfaces
will be 3m.
•
The installation of the appliance shall comform to the Plumbing Code of Australia (PCA).
•
A creepage breaker must be installed adjacent to the power supply.
•
Do not remove, cover or deface any permanent instructions, labels, or the data labels from either the outside of the
unit or inside of unit panels.
•
Required qualified person for relocating, repairing and maintaining the unit instead of doing by yourself.
•
Electric connection work should obey the instructions of local power company, local electric utility and this manual.
•
Never use the wiring and fuse with wrong rated current, otherwise the unit maybe break down and cause fire further
more.
•
Do not insert fingers, rods or other objects into the air inlet or outlet.When the fan is rotating at high speed, it will
cause injury.
•
Never use a flammable spray such as hair spray, lacquer paint near the unit.It may cause a fire.
•
This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental
capabilities or lack of experience and knowledge, unless they have been given supervision or instruction concerning
use of the appliance by a person responsible for their safety. Children should be supervised to ensure that they do
not play with the appliance.
•
Tear apart and throw away plastic packaging bags so that children will not play with them. Children playing with
plastic bags face danger of death by suffocation.
•
Safely dispose of packing materials such as nails and other metal or wood parts that could cause injuries.
•
Ask your dealer or qualified personnel to perform installation work in accordance with this manual. Do not install the
unit yourself. Improper installation could result in water leakage, electric shocks or fire.
•
Be sure to use only specified accessories and parts for installation work. Failure to use specified parts may result in
water leakage, electric shocks, fire, or the unit falling from its mount.
•
Install the unit on a foundation that can withstand its weight. Insufficient physical strength may cause the equipment
to fall and possible injury.
•
Perform specified installation work with full consideration of strong wind, hurricanes, or earthquakes. Improper
installation work may result in accidents due to equipment falling.
DANGER
WARNING
02
Advertisement
Table of Contents
