Nice MIGHTY MULE MMK200 Installation Instructions

MMK200
Installation Instructions
1. OPERATION (FOR PROGRAMMING, PROCEED TO STEP 2)
This MMK200 Digital Keypad is designed for use with Mighty Mule automatic gate operators. The radio format provides unparalleled
security with more than a million different codes.
To activate the automatic gate operator, the user enters their unique 1 to 6 digit long code on the unit's keypad and presses the (
For up to 30 seconds after the last activation, the keypad can be re-triggered by simply pressing the (
stop or reverse the opener quickly, without having to re-enter their code.
The keypad has built-in lighting for use at night or in dark areas. The clear silicone keys are backlit with a pleasing blue glow. Pressing any
key will activate the backlight.
The Mighty Mule gate operator contains a built-in receiver that is
programmed by sending a signal from the keypad. This stores the keypad's
code into the receiver's memory. The receiver will retain its memory even
without power and will only activate from the "memorized" keypad.
PACKAGE INCLUDES
3 AAA batteries included.
KEYPAD
MOUNTING SCREWS
SCREW ANCHORS
2. PROGRAM A KEYPAD CODE TO THE OPENER (MODELS MM371, MM372, MM571, MM572)

On the control board, press and hold the S3 button (
the (S3) button ( ).

While the LED2 button is lit, enter a 1-6 digit code into the keypad. Then PRESS and HOLD the keypad's
BEEPS and the light BLINKS once. Repeat Steps 1 & 2 for any additional keypad codes.
DELETE A KEYPAD CODE: Follow Steps 1 and 2 (above) to delete (overwrite) an existing keypad code.
PROGRAMMING A KEYPAD CODE (MM271 OR MM272)
1. Use the ON/OFF switch on the opener control box to
power the system off.
2. Enter the desired 1-6 digit code into the keypad.
PRESS and HOLD the key, and continue to hold
until instructed to release.
3. While still holding the key, use the ON/OFF switch
on the control box to power the system ON.
4. After the startup beep, there will be a silence for 5-10
seconds, followed by an uninterrupted beep.
5. Release the key after the beep.
DELETING A KEYPAD CODE (MM271 OR MM272)
Follow Steps 1 through 5 to delete the keypad code.
Note: If using the MM271, the gate must be in the closed position to delete an existing keypad code. It can be open or closed to program a
new code.
Digital Keypad
Compatible with Mighty Mule
automatic gate operators:
for Automatic
271, 272, 371W, 372W, 571W
and 572W
Gate Operators
) button again. This allows the user to
KEY FEATURES
TEN KEYS FOR ENTERING
1-6 DIGIT KEYPAD CODES
USING NUMBERS OR LETTERS.
SOFT BLUE LIGHTS
ILLUMINATE THE KEYS
FOR NIGHTTIME USE.
THE KEY STAYS ACTIVE FOR 30 SECONDS
AFTER A CODE IS USED SO THE OPENER
CAN BE STOPPED OR REVERSED.
) until LED2 [beside the S3 button] illuminates and the buzzer sounds. Release
key until the opener


UP
S2
S3
S4
DOWN
WALL MOUNTING

DRIVE THE PROVIDED SCREW
INTO THE MOUNTING SURFACE
(NOT ALL THE WAY).
) button.

ALIGN THE SCREW WITH U-SHAPED
SLOT ON THE BACK OF THE UNIT,
INSERT AND SLIDE DOWNWARD
UNTIL SECURE.
ADJUST THE SCREW DEPTH IF
NEEDED.

REMOVE THE BATTERY ASSEMBLY
TO ACCESS THE SECOND MOUNTING
HOLE (SEE CHANGING BATTERIES,
BELOW).
ALIGN THE SCREW WITH THE
MOUNTING HOLE AND TIGHTEN.
REPLACE THE BATTERY ASSEMBLY.
CHANGING BATTERIES

REMOVE ONE SCREW THEN REMOVE
THE BATTERY CRADLE.

INSTALL 3 FRESH AAA BATTERIES
INTO THE CRADLE.
Mighty Mule Technical Service: 800-421-1587
For more information about the full line of Mighty Mule
Automatic Gate Operators, Gate Openers and Access
Controls visit.
Press the
www.mightymule.com
S3 button ( )
Niceforyou.com
©2024 Nice North America LLC.
Mighty Mule is a registered trademark of Nice North America LLC.
All rights reserved.
KEYPAD OPERATION
DAYTIME OPERATION

ENTER THE KEYPAD CODE

PRESS
USE THE ANCHOR
SUPPLIED IF REQUIRED
1-6 DIGIT KEYPAD CODE THAT
WAS PROGRAMMED INTO THE OPENER
NIGHTTIME OPERATION

PRESS THE LIGHT (

ENTER THE KEYPAD CODE

PRESS
1-6 DIGIT KEYPAD CODE THAT
WAS PROGRAMMED INTO THE OPENER
WARNING: Changes, modifications or adjustments not expressly approved
by Nice North America could void the user's authority to operate this
equipment. There Are No User Serviceable Parts.
NOTICE: This device complies with Part 15 of the FCC Rules. Operation
is subject to the following two conditions: (1) This device may not cause
USE THE ANCHOR
harmful interference, and (2) this device must accept any interference
SUPPLIED IF REQUIRED
received, including interference that may cause undesired operation.
This device complies with Industry Canada License-exempt RSS standards.
Operation is subject to the following two conditions: (1) this device may not
cause harmful interference, and (2) this device must accept any interference,

REMOVE THE OLD BATTERIES FROM
including interference that may cause undesired operation of the device.
THE CRADLE, AND DISPOSE OF THEM
PROPERLY.
KEEP BATTERIES OUT REACH OF CHILDREN. Swallowing batteries can
lead to serious injury or death. If you suspect someone has swallowed a
battery, go to the hospital immediately. Do not induce vomiting or eat or
drink anything.
For more information, call the National Battery Ingestion Hotline: 202-
625-3333.

REPLACE BATTERY CRADLE AND The battery identification number for this product is AAA Alkaline (LR03).
SECURE THE SCREW.
MIGHTY MULE LIMITED WARRANTY
This product is warranted to the original consumer ("You") by Nice North
America against defects in material and workmanship for a period of
twelve (12) months from the date of purchase. This limited warranty
only extends to you if the item was purchased directly from Nice North
America or through an authorized sales partner. Nice North America
will, at its option, either repair or replace any product that it confirms is
defective and eligible for service under this warranty and will return the
repaired or replaced product to you at Nice North America's cost. This
warranty does not apply to damage to the product from negligence,
abuse, abnormal usage, misuse, accidents, acts of god, normal wear
and tear, failure to follow the manufacturer's instructions, or arising from
improper installation, storage or maintenance. Some states do not allow
the exclusion or limitation of incidental and consequential damages,
so the above limitation or exclusion may not apply. This warranty gives
you specific legal rights and you may also have other rights, which vary
from state to state. In order to be protected by this warranty, a copy of
the receipt or other valid proof of purchase must be provided with any
product that is being repaired or replaced under this warranty. In order to
initiate warranty service for your product, please contact Tech Services
at (800) 421-1587 for a Return Authorization Number ("RA") and other
important details.
) BUTTON (TO LIGHT KEYPAD)
WARNING
10021997 Rev-D