Sunx FX-100 Series Instruction Manual

FX-100
production in December, 2007. Hence, this instruction
INSTRUCTION MANUAL
Photoelectric Sensor
FX-100 Series
Thank you very much for using SUNX products. Please read this Instruc-
tion Manual carefully and thoroughly for the correct and optimum use of this
product. Kindly keep this manual in a convenient place for quick reference.
Never use this product as a sensing device for personnel protection.
In case of using sensing devices for personnel protection, use products
which meet laws and standards, such as OSHA, ANSI or IEC etc., for
personnel protection applicable in each region or country.
1 PART DESCRIPTION
Operation indicator
(Orange)
Digital display (Green)
(Threshold value)
<Operating portion>
MODE key
Note : Press MODE key for 2 sec. or more while setting other than RUN mode, to re-
turn to RUN mode.
2

MOUNTING

<When using a DIN rail>
1. Fit the rear part of the mounting section of the
2. Press down the rear part of the mounting
to the DIN rail.
it.
hook on the rear portion of the mounting section is likely to break.
<When using screws with washers>
Use M3 screws with washers for mounting.
less.
1. Snap the fiber lock lever down, till it stops
completely.
2. Insert the fiber cables slowly into the inlets
until they stop. (Note 1)
tion, till it stops.
it is inserted.
the sensing performance will deteriorate.
Digital Fiber Sensor
MJE-FX100 No.0009-43V
WARNING
ON key / OFF key /
Set value UP key Set value DOWN key
MODE key
Digital display (Red)
(Incident light intensity)
ON key / OFF key /
Set value UP key Set value DOWN key
2
35mm width DIN rail
1
2
1
Fiber lock
lever
-
2
Fiber
FD-G4 or FD-FM2, insert the
3

WIRING

Connection method
Insert the cable with connector
this product's connector area as shown in the
right figure.
Disconnection method
Pressing the release lever of the cable with con-
nector, pull out the connector.
Note: Take care that if the connector is pulled out without
pressing the release lever, cable or connector may
break.
<Connector pin arrangement>
1
2
3
4
4 I/O CIRCUIT DIAGRAMS
<NPN output type>
8V
Internal circuit
<PNP output type>
Internal circuit
*1
Non-voltage contact or NPN open-collector transistor
1
High (+8V to +V DC or Open): Invalid
5

RUN MODE

<Digital display>
When turning ON the power, the product name is indicated on the green
digital display, while the emission frequency is indicated on the red digital
display. Then switches into RUN mode [digital display (green: threshold
value, red: incident light intensity)].
When selecting emission halt in the external input setting mode and re-
ceiving the signal externally, "
M3 screw
with washer
When selecting ECO in the external input setting mode, key operation on
the main body is invalid during external input.
When selecting 2-point teaching in the external input setting mode, "
is indicated on the green digital display after inputting the first point.
When ECO setting mode is ON, the digital display turns off in approx. 20
sec. In case of lighting up the digital display again, press any key for 2
3
sec. or more.
For the settings of external input and ECO, refer to "
Fine adjustment of threshold value can be done when in RUN mode.
Press the set value UP key or set value DOWN key to change threshold
value. (Hold down the key to make the value change faster.)
The threshold value is stored after 3 sec.
Connector pin No. Terminal name
1 +V
2 Output
3 External input
4 0V
Color code of cable with connector
Connector pin No.
(Brown) +V
Load
(Black) Output
100mA max.
(White) External input
(Blue) 0V
Users' circuit
Color code of cable with connector
Connector pin No.
(Brown) +V
(White) External input
100mA max.
(Black) Output
Load
(Blue) 0V
Users' circuit
*2
Non-voltage contact or PNP open-collector transistor
or
Low (0 to +0.6V DC or Open): Invalid
<When turning ON the power> <RUN mode>
Automatic
Product Emission Threshold
name frequency value
" is indicated on the red digital display.
<When in RUN mode>
Threshold Incident light
value intensity
Cable with
connector
into
CN-14A-C
Release
lever
+
12 to 24V DC
±10%
–
*1
*2
+
12 to 24V DC
±10%
–
or
Incident light
intensity
"
Pro Mode."