Switch Position; Replacing The Power Cable; Cleaning, Maintenance And Ordering Of Spare Parts - EINHELL TC-ID 720/1 E Original Operating Instructions

6.3 Preselecting the speed (Fig. 6/Item 6)
•
The speed setting ring (6) enables you to
define the maximum speed. The ON/OFF
switch (5) can only be pressed to the defined
maximum speed setting.
•
Set the speed using the setting ring (6) on the
ON/OFF switch (5).
•
Do not attempt to make this setting whilst the
drill is in use.
6.4 Clockwise/Counter-clockwise switch
(Fig. 6/Item 7)
•
Change switch position only when the drill is
at a standstill!
•
Switch the direction of the hammer drill using
the clockwise/counter-clockwise switch (7):
Direction
Clockwise (forwards and drill)
Counter-clockwise (reverse)
6.5 Drill / hammer drill selector switch
(Fig. 7/Item 3)
Change switch position only when the drill is at a
standstill!
Drill
Drill / hammer drill selector switch (3) in the drill
position. (Position A)
Use for: Wood, metal, plastic
Hammer drill
Drill / hammer drill selector switch (3) in the ham-
mer drill position. (Position B)
Use for: Concrete, rock, masonry
6.6 Tips for working with your hammer drill
6.6.1 Drilling concrete and masonry
•
Switch the Drill/Hammer drill selector switch
(3) to position B (Hammer drill).
•
Always use carbide drill bits and a high speed
setting for drilling into masonry and concrete.
6.6.2 Drilling steel
•
Switch the drill / hammer drill selector switch
(3) to position A (drill).
•
Always use HSS drill bits (HSS = high speed
steel) and a low speed setting for drilling
steel.
•
We recommend that you lubricate the hole
with a suitable cutting fluid to prevent unne-
Anleitung_TC_ID_720_1_E_SPK13.indb 17 Anleitung_TC_ID_720_1_E_SPK13.indb 17
GB
cessary drill bit wear.
6.6.3 Starting holes
If you wish to drill a deep hole in a hard material
(such as steel), we recommend that you start the
hole with a smaller drill bit.
6.6.4 Drilling tiles
•
To start the hole, switch the drill / hammer drill
selector switch (3) to position A (drill).
•
Switch the drill / hammer drill selector switch
(3) to position B (hammer drill) as soon as the
drill bit has passed through the tiles.

7. Replacing the power cable

Switch position

Danger!
Pushed in to the
If the power cable for this equipment is damaged,
right
it must be replaced by the manufacturer or its
after-sales service or similarly trained personnel
Pushed in to the
to avoid danger.
left
8. Cleaning, maintenance and
ordering of spare parts
Danger!
Always pull out the mains power plug before star-
ting any cleaning work.
8.1 Cleaning
•
Keep all safety devices, air vents and the
motor housing free of dirt and dust as far as
possible. Wipe the equipment with a clean
cloth or blow it with compressed air at low
pressure.
•
We recommend that you clean the device
immediately each time you have finished
using it.
•
Clean the equipment regularly with a moist
cloth and some soft soap. Do not use
cleaning agents or solvents; these could at-
tack the plastic parts of the equipment. Ensu-
re that no water can seep into the device. The
ingress of water into an electric tool increases
the risk of an electric shock.
8.2 Carbon brushes
In case of excessive sparking, have the carbon
brushes checked only by a qualifi ed electrician.
Danger! The carbon brushes should not be rep
laced by anyone but a qualifi ed electrician.
- 17 -
26.10.2023 16:23:23 26.10.2023 16:23:23