Attention: This service manual is only for service personnel to take reference with. Before servicing please read the following points carefully. Safety precautions Please read the “Points for attention for the Maintenance & Repair of PDP” and “Criterion for Identifying the Defects on Screen” as below, before inspecting and adjusting the TV set. 1.
Page 4
narrow and in bad ventilation. 1.10 There are quite a number of circuits in PDP that are integrated ones. Please be on guard against static electricity. During maintenance operation be sure to cover yourself with anti-static bag and before operation make sure to have it sufficiently grounded. 1.11 There are a big number of connection wires distributed around the screen.
too big screw. 1.20 Care must be taken to guard against dust during assembling or dismantling, especially to avoid dirt from falling in between the screen and the glass lest it should harm the receiving and viewing effect. 1.21 There is piece of insulator stuck on the rear chassis corresponding to the power supply board. It is used to isolate the cool part from the hot part.
Page 6
set ISP back to 0. If the picture can’t display when upgrading, it needs to weld JB1 on the main board. Please disconnect JB1 again after upgrading. 3.1 Initialization Enter factory menu, select “OPTION”, “EEPROM” and “HOTEL OPTION” sub-menu, adjustment of items to see table1.
Page 7
normal, if not, enter COLOR TEMP menu, set ALL COLOR to 0 and fine adjust according the method of 3.3.1 c) b. connect VG-848 signal of YPBPR to YPBPR terminal and input TIMING972(1080i/60HZ) 100% color bar of PAT976(include black/white bar), Enter submenu of ADC ADJ, Select AUTOTUNE and wait for OK display.
Working principle analysis of the unit The RF signal received by antenna will be sent to tuner TUNER101, then IF signal will be obtained through high amplifier and mixed frequency, through pre-intermediate amplified by V101, then it will be sent to acoustic surface-wave Z102 to do IF filter and get better IF characteristics, then it will be sent to N101 (R2S10401) to do intermediate amplification, phase-locked loop VCO and synchronous wave detection to get composite video signal TV-VIDEO;...
Trouble shooting 1. No raster Turn on power supply, check if the red indicator is light in the STANDBY? Check if PIN9 (5V) of XS12 Press POWER button in the on the main board is normal? unit or sensor control and check the indicator.
Page 17
2. Raster, but no picture Check if the unit button Does display remote control menu in screen when operation? press menu button? Check channels have signal? HDMI/VGA/YPRPB Enter factory-menu, Which is no signal initialization EEPROM, of channels? Replace then turn off the TV, main board turn on again, display Replace...
Page 18
3.no sound Check if PIN2, 3,13 and Check PIN5 14 voltage of NV4 is PIN11 output wave of Replace NV4 normal? Check power supply Check PIN10 wave of Replace NS2 N101 Replace N101 Check PIN11 wave of TUNER Replace TUNER...
Page 25
APPENDIX-A: Main assembly 9432HU3512 MAIN COMPONENT AND IT'S NO. NAME N101 R2S10401 (5271040101) Main board 6HU06801E0 R2S15102 (5271510201) MST9U19A (5270019001) IR board 6HU0660910 Key board 6HU0660510 Remote control RC-Y57-0A 6010Y05701 PDP32F1 Panel 5205321201 APPENDIX-A: Main assembly 9432HU3514 MAIN COMPONENT AND IT'S NO. NAME N101 R2S10401...
Page 27
PART LIST OF EXPLODED VIEW EDSCRIPTION front cabinet fiter glass panel push board main frame push board main board socket wall mounting bracket back cabinet speaker connection right speaker stand speaker back cover back baffle left speaker connection bracket push board power socket push board decorative bar...