Related Manuals for Emerson PACSafe SXF262
Summary of Contents for Emerson PACSafe SXF262
- Page 1 User Guide GFK-3236B Apr 2023 PACSafe™ SXF262 Demo Kit (IC225DEM001) USER GUIDE GFK-3236B April 2023...
-
Page 2: Table Of Contents
PACSafe™ SXF262 Demo Kit (IC225DEM001) Warnings GFK-3236B Apr 2023 Contents Contents ..................i About This Guide ..................1 Product Overview – Demo Kit Contents ..........1 Components Needed to Run the Demo ........... 2 Software Installation ................. 3 Demo Project Software ................4 Appendix A: Troubleshooting - Factory Test .......... - Page 3 PACSafe™ SXF262 Demo Kit (IC225DEM001) Warnings GFK-3236B Apr 2023 WARNING It is the responsibility of the Qualified Person who configures, installs, or maintains the PACSafe Safety Controller Carefully read, understand, and follow the information in the PACSafe Configurable Safety Controller User •...
-
Page 4: About This Guide
These documents are available to download at the Support link provided at the end of this manual. Product Overview – Demo Kit Contents The PACSafe Demo frame with a PACSystems CPE100 and PACSafe SXF262 Safety Controller • External 24 VDC Class 2 power supply with cord •... -
Page 5: Components Needed To Run The Demo
PACSafe™ SXF262 Demo Kit (IC225DEM001) GFK-3236B Apr 2023 Figure 1: PACSafe Demo Components Needed to Run the Demo To run the PACSafe demo, the user will need the following components: 1. A PC running a licensed copy of PME Logic Developer and PME View to load, run, and view the SXF262 CPE100 controllers. -
Page 6: Software Installation
Machine Edition – Logic Developer PLC, Getting Started Guide, GFK-1918. After PME 9.8 is fully installed, download and install the PACSafe Studio Software. To Download the PACSafe Configuration Software from the Emerson Website: 1. Download the latest version of the software from https://emerson-mas.force.com/communities/en_US/Download/PACSafe-Configuration-Tools... -
Page 7: Demo Project Software
For the Standard PROFINET Demo with HMI: 1. Go to the landing page for the PACSafe Demo (IC225DEM001) at the Customer Knowledge Center: https://emerson-mas.force.com/communities 2. Download the latest version of the PACSafe PROFINET demo project: PACSafe_Demo_Std PN wHMI R1.zip 3. Using PME to restore the project. The PACSafe Controller Program will automatically be placed in the PME Project Folder. - Page 8 PACSafe™ SXF262 Demo Kit (IC225DEM001) GFK-3236B Apr 2023 6. Open the PACSafe Project entitled PACSafe CSC Demo Std PN wHMI R1.xcc Note: the PME Project Folder default location is typically: C:\Users\Public\Documents\GE Intelligent Platforms\PME\SecurWORX\Local\FrameworX 7. Connect to the SXF262 using the supplied USB Cable. 8.
- Page 9 PACSafe™ SXF262 Demo Kit (IC225DEM001) GFK-3236B Apr 2023 4. Navigate to PME Utilities and click on PROFINET DCP to set the PROFNET parameters on the PACSafe Controller: a. Device Name: pacsafe-pn1 b. IP Address: 192.168.001.002 c. Subnet Mask: 255.255.255.000 5. Refresh the Device List to verify PACSafe Controller PROFINET settings. 6.
- Page 10 PACSafe™ SXF262 Demo Kit (IC225DEM001) GFK-3236B Apr 2023 7. Set PME to monitor the CPE100 program. a. In PME, right-click on the CPL100 Target. Then connect to the PLC. 8. Go back to the PACSafe Tool. Note: If the PACSafe Tool was closed after Step 4, the user will need to open the tool again. 9.
-
Page 11: Appendix A: Troubleshooting - Factory Test
PACSafe™ SXF262 Demo Kit (IC225DEM001) GFK-3236B Apr 2023 Appendix A: Troubleshooting - Factory Test IC225DEM001 – Factory Test Instructions R004: 1. Perform any wiring checks required before connecting the power. 2. Set the two toggle switches (Figure 4) so the switch is lowest on the side closest to the edge of the unit. Note: This is the OFF position (sensor indicates unsafe condition) for these two toggle switches. - Page 12 PACSafe™ SXF262 Demo Kit (IC225DEM001) GFK-3236B Apr 2023 9. Remove the micro-USB memory stick and put it back with the factory test materials. 10. Press the RESET button on the panel. a. The IO8 LED should go off. b. The SO1a & SO1b LEDs should come ON. 11.
- Page 13 PACSafe™ SXF262 Demo Kit (IC225DEM001) GFK-3236B Apr 2023 b. Toggle the Light Screen (LS) switch on the outside of the unit. After approximately 10 seconds, the IO7 and SO2b LEDs will turn off. d. Toggle the LS switch on the center of the unit and the SO2b LED will turn on. e.
-
Page 14: Appendix B: Pacsafe Demo Schematic
PACSafe™ SXF262 Demo Kit (IC225DEM001) GFK-3236B Apr 2023 Appendix B: PACSafe Demo Schematic Figure 9: PACSafe Demo Schematic... -
Page 15: General Contact Information
© 2023 Emerson. All rights reserved. Emerson Terms and Conditions of Sale are available upon request. The Emerson logo is a trademark and service mark of Emerson Electric Co. All other marks are the property of their respective owners.