Table of Contents
Advertisement
General Information
Heat
dissipation
700
Watts
(2,3
8
9
Btu/hr)
maximum
Dimensions
Height:
720
mm
(28.4
in.)
Width: 375
mm
(14.8
in.)
Depth:
774
mm
(3
0.5
in.)
including baffle
Weight
Net
Installed:
Disc
+ Tape Drive 109
kg
(2
3
9 lb)
Shipping:
Disc
Drive 135 kg
(297
lb)
Tape Drive
9
kg
( 1
9 lb)
1-7.
ENVIRONMENTAL
REQUIREMENTS
Before
installing
an
HP
7914CT,
refer to the
"Site
Environmental
Requirements
Manual",
publication
number
5955-3456.
Copies
of
this
publication
are
available
from
your
local
Hewlett Packard
Sales
and
Support
Office,
and
a
copy
is
shipped with every
HP
7914CT.
1-8.
SAFETY
•
CSA
Certified
to
CSA
22.
2
No.
1
54
•
Meets
all
applicable safety standards of
IEC 380 and IEC
435.
•
UL
Listed
to
UL
1
14
and
UL
478
1-9.
SYSTEM
CONFIGURATIONS
For
specific
configurations
the
appropriate
System Configuration Guide
should be
consulted.
However,
the following general conditions should
be noted:
•
Total cable length
is
limited
to
one metre
per equivalent
load.
•
Each
controller places
one
equivalent load
on each
of
the
HP-IB
lines.
•
The
disc
drive
includes
one metre
of
internal cabling.
1-10.
OPTIONS AVAILABLE
01
5
-
220V
50
Hz
or
240V
50
Hz
operation
140
-
Orders
the
disc
drive
only,
the
HP
9144A
cartridge tape drive
is
deleted.
1-11.
ACCESSORIES
SUPPLIED
|
NOTE
The
rear
panel
sound
baffle
is
shipped
in
the
disc drive's
accessory
box.
This
component must
be
fitted to
the rear
panel before operating the subsystem.
Fitting
instructions
are
given
in
paragraph 2-38.
Shipped with
the
HP
7914CT:
HP
791
4CT
Installation,
Operating
and
Service
Manual:
35414-90000
HP
7914CT
Operator
Controls
Card:
.35414-90001
HP
791
1,
7912
and
7914
Operator
Instructions:
07912-90901
HP
791
1,
7912
and
7914
Operating
and
Installation
Manual:
07912-90902
Site
Environmental Requirements Manual:
5953-3456
Two
HP-IB
Cables
(1
-metre
long):
10833A
Two
Module
Locks:
9221
1-40002
TWO
Power
Cables: One
suitable
for
country of
destination*
and
one
for
connecting
the
HP
9144A
to
the
HP
7914 power
distribution unit
Shipped with the
HP
9144A:
HP
9144A
Operator's
Manual:
09144-90000
Tape
Cartridge
(600
foot.,
67
Mbyte):
S8140LC**
Tape Head
Cleaner
Solution***:
8500-1251
Lint-free
Swabs
(plastic
shaft)***:
9300-0767
Power
Cable:
Suitable for
country
of destination*
*
One
of these
power
cords
will
be
a
spare.
** "C"
denotes factory
certified tapes.
***
Periodic cleaning
of the
HP
9
144
A
read /write
heads
is
required
to
ensure
correct operation (after
a
new
cartridge
is
inserted,
when
read
errors
occur
or
at
least
once a
week).
1-3
Advertisement
Table of Contents
