Advertisement
INSTALLATION INSTRUCTIONS
RADIO INSTALLATION
(FIG 4)
REAR SPEAKER
INSTALLATION-STATION
WAGON
(Fig. 3)
1.
Install antenna as instructed by
antenna
template pravided
.
2
.
Remove radio opening
cover.
3.
Position the radio against radio open
i ng
from behind instrument
panel.
4
.
Hold radio in position and place trim plate over controi shafts fram front of the
instrument panel. (The word TOP must be positioned
praperly.)
5. Secure radio in radio opening with the two
1
12"
nuts.
6.
Press
knobs on contral shafts.
(Disc knob with red mark should be on right
side
with
mark
in top
position:
)
7
.
Attach one
end of the support strap to the stud on the rea
r of
the radio. Attach
other end of
the support strap
to
an appropriate spot on the body sheet metal
with
#
10
x
1
/ 2 "
screw·washer
assembly:
(Drill .136 diameter hole for screw.)
FRONT SPEAKER INSTALLATION
(FIG.
4)
1.
Remove attaching
hardware
from passenger support
handle.
Do
not lose attach
·
ing
hardware.
2. To
facilitate installation,
detach
pilot
light
bracket (l screw) and glove
com·
partment box (2 bolts).
3. Attach speaker to mounting plate with word
TOP
on
mounting plate
facing
speaker.
4.
Install speaker assembly with support handle attaching hardware
as shown
in
Figure 3. Be sure word TOP on mounting plate is positioned toward
car
raof.
NOTE: Two existing twist tabs, one located above and one located below the
front speaker grille, must be bent against the instrument panel
to
permit flush
mounting of the speaker
assembly.
5.
Replace pilot
light
bracket and glove compartment box.
REAR SPEAKER INSTALLATION-All SEDANS (Fig. 2)
1.
Remove metal knock·out from rear deck panel.
2. Cut speaker opening into upholstered hardboard panel using opening
in
rear
deck panel as a guide,
3. Center the speaker grille over speaker opening and mark the center of each of
the four speaker grille mounting holes.
4.
Drill a 0.190" diameter hole
(#
9 drill) at each mark through both hardboard
panel and metal rear deck panel.
5
.
Attach speaker and speaker grille with four
#
8 x 11,4" machine screws and four
#
8 nut·washer assemblies.
1.
Detach right rear trim panel.
2.
Locate center for speaker opening as indicated in Figure 3 and provide a 6
"
wide
by 4
"
high eliptical opening in trim panel.
'.
3.
Drill four
.190"
diameter holes around speaker open ing as indicated in Figure 3
using the speaker grille as guide.
4.
'
Mount speaker and speaker grille to trim panel with speaker terminals facing
toward rear of vehicle.
'
5.
Starting
at fader control, route rear speaker leads along right side
of vehicle,
dressing leads behind kick pad
,
then under floor mat and scuff plates
.
Continue
routing under upholstered 'and metal panels to rear speaker.
6
.
Connect leads to rear speaker and replace right rear trim panel.
FADER CONTROl INSTAllATION
(FIG
.
1)
1.
Drill
hole in instrument panel at location shown in Figure l
2
.
Install
fader
contra
I.
3.
Route fader
contral
leads as
shown in Figure 2. (Route
frQnt
speat<.<..
fader controi
as near as possible along
front
of
'
instrument panel
away
firewall.
Fold and tape excess front
speaker leads neatly.)
ElECTRICAl CONNECTIONS
1.
Connect power
lead (
" A"
lead) to accessory
side of
ignition
switch.
2.
Insert antenna lead
into antenna re ceptacle.
3. Connect fader controi leads
as
show
in
Figure 2. (Be sure insulatian sleeves are
installed.)
ANTENNA TRIMMER ADJUSTMENT
1. Read radio operating instructions.
2.
Extend antenna mast to minimum height of 30".
3. Turn radio on and tune to a weak AM station (or random noise level between
stations) between 1400 and 1600 KHz.
4. Adjust antenna trimmer for maximum volume.
Advertisement
