Elimko E-KC-100 Series User Manual

E-KC-100 SERIES HEAD MOUNTED TYPE
TEMPERATURE CONVERTER USER MANUAL
The E-KC-100 converter is designed for use in an industrial environment.
 The package of the
cert f cate.
 After open ng the package, please v sually check whether the type of the transm tter s su table
for the order, whether the above-ment oned parts are m ss ng and whether the transm tter has
been damaged dur ng sh pment.
 Before nstall ng and operat ng the controller, please read the user manual thoroughly.
 The nstallat on and conf gurat on of the controller must only be performed by a person qual f ed n nstrumentat on.
 Keep the un t away from flamable gases, that could cause explot ons.
 Do not use alcohol or other solvents to clean the transm tter. Use a clean cloth soaked n water t ghtly squeezed
to gently w pe the outer surface of the transm tter.
 It s not used n med cal appl cat ons.

1. DESCRIPTION

E-KC-100 series transmitters are microprocessor based industrial
instruments in plastic case. E-KC-100 transmitters are used to
convert the thermocouple and resistance thermometer signals into
standard 4-20 mA The configuration of the transmitter is done by
PC, using a software programme supplied by Elimko.
The RS 232 connection hardware is also available from Elimko.

2. TECHNICAL SPECIFICATIONS

2.1. OPERATING RANGE and EASURING ACCURACY
(at 24 V supply voltage and 25°C ± 3°C ambient temperature)
LOWER
STANDARD
SENSOR
RTD Pt-100 IEC 60751 -200°C
B
E -200°C
J -200°C
K -200°C
IEC 60584
N -200°C
T/C
R
S
T -200°C
L -200°C
DIN 43710
U -200°C
mV -2000mV
If the input type and scale is not specified while ordering, factory settings are;
Input Type : Pt-100, and Scale : 0-200°C.
KY-KC100-0224-1
E-KC-100 converter conta ns; the
M
UPPER MINIMUM
LIMIT
LIMIT SPAN
850°C 50°C ±0.25°C
100°C 1800°C 100°C ±2.00°C
840°C 50°C ±0.50°C
1120°C 50°C ±0.50°C
1360°C 50°C ±0.50°C
1300°C 50°C ±0.50°C
-40°C 1760°C 100°C ±1.00°C
-40°C 1760°C 100°C ±1.00°C
400°C 50°C ±0.50°C
900°C 50°C ±0.50°C
600°C 50°C ±0.50°C
500mV 25mV ±0.075mV
Converter , user manual and guarantee
2.2. General Specifications
Ele ctrical
Supply Voltage
Voltage Drop
Environmental Conditions:
Operating Temperature
Protection Class
Cal brat on Temp.
Mechan cal:
D mens ons
We ght (approx.)
Connect on Cables
Res stance Thermometer (RTD) / Res stance Input:
Sensor Connect on
Maximum Wire Resistance
Error Signaling
Thermocouple (TC) / mV Input:
Input Impedance
Maximum Wire Resistance
Cold Junction
Compensation (CJC)
Error S gnal ng
Output:
Output Signal
ACCURACY
Load Resistance
A/D D/A
Operating Influences:
Ambient Temperature
CJC Error (For TC Inputs)
EMC Immunity
±0.1%
Span
Electromagnetic Compatibility:
The E-KC-100 meets the requirements of
TS EN 61326-1.
:
10.0 - 30 V DC
9.0 V
-10°C to +55°C
IP 00,
IP 66 (DIN 43729 mounted on
type B head)
25°C ±3°C
Ø 44.0 mm x 21.5 mm
40 g
Max. 1.5 mm² (AWG 16)
3-Wire
100 
Wire Break (Output current
can be configured Up / Down.)
> 10 M
100 
Constant, Internal NTC,
External Pt-100 (Configurable)
W re Break (Output current
can be conf gured Up / Down.)
4 - 20 mA or 20 - 4 mA
[V -10]× 50
supply
(600 W
< ± 0.01% / °C
< ± 1.0 °C
< ± 0.5% Span
KY-KC100-0224-1
W
at 22 V DC)