Table of Contents
Advertisement
MHC-V13
PANEL TEST MODE
This mode is used to check the screen display panel, LEDs, model
name, destination, software version and buttons.
Procedure:
1. Press [
] button to turn on the system.
1
2. Press [MIC/GUITAR LEVEL -] and [] buttons simultaneously
for 3 seconds.
3. All LEDs and segments in screen display panel are lighted up.
This is the display check mode.
4. Press [TUNING + >] button. Model information appears on
the screen display panel.
5. Press [TUNING + >] button again. Destination information
appears on the screen display panel.
6. Press [TUNING + >] button. Serial number appears on the
screen display panel.
7. During the serial number display, press [TUNING + >]
button. Each time [TUNING + >] button is pressed, the screen
display panel shows the version of each category software in the
following sequence: MCU, SOC, BT, BTE and return back to
model information display.
8. Press [TUNING – .] button, the buttons check mode is
activated.
9. In the buttons check mode, the screen display panel displays
"K 0".
Each time a button is pressed, "K" value increases. However,
once a button has been pressed, it is no longer taken into account.
After all the buttons have been pressed, "K" value will toggle
between "OK" and "K20".
10. Press [MIC/GUITAR LEVEL -] and [] buttons simultaneously
for 3 seconds to exit.
USER RESET
The user reset clears all data including preset data stored in the data
fl ash to initial conditions.
Procedure:
1. Press [
] button to turn on the system.
1
2. Press [GUITAR] and [FIESTA] buttons simultaneously for 3
seconds.
3. "RESET" appears on the screen display panel. After that, the
screen display panel becomes blank for a while, and the system
goes to demo mode.
HISTORY MODE
This mode is used to check important data stored in the system when PROTECTOR happened.
Procedure:
1. During demo mode, press [FIESTA] button and [MIC/GUITAR LEVEL +] button for 5 seconds to mode into history mode.
2. Press the [TUNING + >] button or [TUNING – .] button to check history data stored.
Display on screen display panel
P
C
O
U
P
T
1
*h
*h
*h
2
*h
*h
*h
F
V
O
L
B
A
S
S
3. To release from this mode, press [
17
TEST MODE
N
T
※
※
※
※
*h
*h
*m
*m
*h
*h
*m
*m
※
※
※
※
※
※
※
※
※
] button.
1
SECTION 3
COLD RESET
This mode is used to reset all the user settings to factory setting.
Execute this mode when returning the set to the customer.
Procedure:
1. Press [
] button to turn on the system.
1
2. Press [MIC/GUITAR LEVEL +] and [] buttons simultaneously
for 3 seconds.
3. "COLD RST" appears on the screen display panel. The system
automatically turn on and off once. After that, "SONY" appears
on the screen display panel. Please be sure that the system stay
at demo mode fi nally before switch off the power supply.
SHOP FRONT DEMO
The playback started automatically and the " * DEMO * " appears
on the screen display panel.
This is the Shop Front Demo mode which is activated by the shop
front.
To release from Shop Front Demo
1. Press [MEGA BASS] and [B] buttons simultaneously for 5
seconds.
2. The message "STANDBY" appears on the screen display panel
and the system goes to demo mode.
No. of time protector happened (0 ~ 99)
※
※
Refer to protect type description (E00~E09)
Single Power On Time until protector happened (0~99999 hours,
0~99 minutes)
Total Power On Time [ no consider protector happened ]
(0~99999 hours, 0~99 minutes)
Input Function during protector happened
※
Volume setting (MIN / 1 - 50 / MAX)
※
※
MEGA BASS setting (OFF / ON)
Sony CONFIDENTIAL
For Authorized Servicer
Description
SYS SET
Advertisement
Table of Contents
