Sony MHC-V13 Reference Manual

Home Audio System
Equipo de audio para
el hogar
MHC-V13
©2020 Sony Corporation
Printed in Malaysia
https://www.sony.net/
English Home Audio System
Before operating the system, please read this guide thoroughly and retain it for
future reference.
WARNING
To reduce the risk of fire, do not cover the ventilation opening of the appliance
with newspapers, tablecloths, curtains, etc.
Do not expose the appliance to naked flame sources (for example, lighted
candles).
To reduce the risk of fire or electric shock, do not expose this appliance to
dripping or splashing, and do not place objects filled with liquids, such as vases,
on the appliance.
As the main plug is used to disconnect the unit from the mains, connect the unit
to an easily accessible AC outlet. Should you notice an abnormality in the unit,
disconnect the main plug from the AC outlet immediately.
Do not install the appliance in a confined space, such as a bookcase or built-in
cabinet.
The unit is not disconnected from the mains as long as it is connected to the AC
outlet, even if the unit itself has been turned off.
Indoor use only.
The following information is only applicable to equipment sold
in countries/regions comply to EMC regulation.
This equipment has been tested and found to comply with the limits set out in
the EMC regulation using a connection cable shorter than 3 meters.
CAUTION
Risk of explosion if the battery is replaced by an incorrect type.
Do not expose batteries or appliances with battery-installed to excessive heat,
such as sunshine and fire.
CAUTION
Caution – use of controls or adjustments or performance of procedures other than
those specified herein may result in hazardous radiation exposure.
This appliance is classified as a CLASS 1 LASER product under IEC 60825-1:2014.
Do not place this product close to medical devices
This product (including accessories) has magnet(s) which may interfere with
pacemakers, programmable shunt valves for hydrocephalus treatment, or other
medical devices. Do not place this product close to persons who use such medical
devices. Consult your doctor before using this product if you use any such
medical device.
For customers in Australia and India
Disposal of old electrical & electronic equipment
(applicable in the European Union and other
countries with separate collection systems)
Troubleshooting
If error code appears on the display
See the following table for the corrective action.
Error code Corrective action
"PT S0" / Immediately unplug the AC power cord (mains lead), and check
"PT S5" / if anything is blocking the ventilation openings of the unit. After
"PT S6" / you have checked and found no problems, reconnect the AC
"PT T0" / power cord (mains lead), and turn on the system. If the issue
"PT T5" / persists, contact your nearest Sony dealer.
"PT T6"
"PT SX" / Contact your nearest Sony dealer.
"PT TX"
("X" is a number
other than 5
and 6)
Precautions
When carrying the unit
To avoid damaging the disc mechanism, perform the following procedure before
carrying the unit.
Use the controls on the unit to perform this operation.
1
Remove the disc.
Press PUSH OPEN/CLOSE to open and close the disc lid.
2
Press  to turn off the system.
3
After "STANDBY" disappears, unplug the AC power cord (mains
lead).
Notes on discs
• Before playing, wipe the disc with a cleaning cloth from the center outward to
the edge.
• Do not clean discs with solvents, such as benzine, thinner, or commercially
available cleaners or anti-static spray intended for vinyl LPs.
• Do not expose discs to direct sunlight or heat sources such as hot air ducts, nor
leave them in a car parked in direct sunlight.
On safety
• Completely disconnect the AC power cord (mains lead) from the wall outlet
(mains) if it is not going to be used for an extended period of time. When
unplugging the system, always grip the plug. Never pull the cord itself.
• Should any solid object or liquid get into the system, unplug the system, and
have it checked by qualified personnel before operating it again.
• AC power cord (mains lead) must be changed only at the qualified service shop.
On handling the system
• This system is not drip-proof or waterproof. Make sure not to splash water on
the system or clean it with water.
• Do not leave the disc lid open when not in use. Dust may enter and cause
malfunction.
On placement
• Do not place the system in an inclined position or in locations that are extremely
hot, cold, dusty, dirty, or humid or lacking adequate ventilation, or subject to
vibration, direct sunlight or a bright light.
• Be careful when placing the system on surfaces that have been specially treated
(for example, wax, oil, polish) as staining or discoloration of the surface may
result.
• If the system is brought directly from a cold to a warm location or is placed in a
very damp room, moisture may condense on the lens inside the unit, and cause
the system to malfunction. In this situation, remove the disc, and leave the
system turned on for about an hour until the moisture evaporates.
On heat buildup
• Heat buildup on the unit during operation is normal and is not a cause for
alarm.
• Do not touch the cabinet if it has been used continuously at a high volume
because the cabinet may have become hot.
• Do not obstruct the ventilation holes.
On the speaker system
The built-in speaker system is not magnetically shielded, and the picture on
nearby TV sets may become magnetically distorted. In this situation, turn off the
TV, wait 15 to 30 minutes, and turn it back on. If there is no improvement, move
the system far away from the TV.
5-014-534-22(1) Cleaning the cabinet
Clean this system with a soft cloth slightly moistened with a mild detergent solution.
Do not use any type of abrasive pad, scouring powder, or solvent, such as thinner,
benzine, or alcohol.
On BLUETOOTH® communication
• BLUETOOTH devices should be used within approximately 10 meters
(unobstructed distance) of each other. The effective communication range may
become shorter under the following conditions:
Reference Guide
– When a person, metal object, wall or other obstruction is between the devices
with a BLUETOOTH connection.
Guía de referencia
– Locations where a wireless LAN is installed.
– Around microwave ovens that are in use.
– Locations where other electromagnetic waves are generated.
• BLUETOOTH devices and wireless LAN (IEEE 802.11b/g/n) equipment use the
same frequency band (2.4 GHz). When using your BLUETOOTH device near a
device with wireless LAN capability, electromagnetic interference may occur.
This could result in lower data transfer rates, noise, or inability to connect. If this
happens, try the following remedies:
– Use this system at least 10 meters away from the wireless LAN equipment.
– Turn off the power of the wireless LAN equipment when using your
BLUETOOTH device within 10 meters.
– Use this system and BLUETOOTH device as closer to each other as possible.
• The radio waves broadcast by this system may interfere with the operation of
some medical devices. Since this interference may result in malfunction, always
turn off the power on this system and BLUETOOTH device in the following
locations:
– In hospitals, on trains, in airplanes, at gas stations, and any place where
flammable gases may be present.
– Near automatic doors or fire alarms.
• This system supports security functions that comply with BLUETOOTH
specifications to ensure secure connections during communication using
BLUETOOTH technology. However, this security may be insufficient depending
on the setting contents and other factors, so always be careful when performing
communication using BLUETOOTH technology.
• Sony cannot be held liable in any way for damages or other loss resulting from
information leaks during communication using BLUETOOTH technology.
• BLUETOOTH communication is not necessarily guaranteed with all BLUETOOTH
devices that have the same profile as this system.
• BLUETOOTH devices connected with this system must comply with the
BLUETOOTH specification prescribed by the Bluetooth SIG, Inc., and must be
certified to comply. However, even when a device complies with the
BLUETOOTH specification, there may be cases where the characteristics or
specifications of the BLUETOOTH device make it impossible to connect, or may
result in different control methods, display or operation.
• Noise may occur or the audio may cut off depending on the BLUETOOTH device
connected with this system, the communications environment, or surrounding
conditions.
About the Voice Guidance
IMPORTANT: THE VOICE GUIDANCE FOR THIS SYSTEM IS ONLY
AVAILABLE IN ENGLISH.
Depending on the status of the system, the voice guidance outputs from the
system as follows:
• When setting the system to the pairing mode: "BLUETOOTH pairing"
• When connected to a BLUETOOTH device: "BLUETOOTH connected"
• When disconnected from a BLUETOOTH device: "BLUETOOTH disconnected"
• When setting the output mode during the Stereo Pair function: "Left/Right"
License and Trademark Notice
• "CD" logo is trademark.
• WALKMAN® and WALKMAN® logo are registered trademarks of Sony
Corporation.
• MPEG Layer-3 audio coding technology and patents licensed from Fraunhofer
IIS and Thomson.
• Windows Media is either a registered trademark or trademark of Microsoft
Corporation in the United States and/or other countries.
• This product is protected by certain intellectual property rights of Microsoft
Corporation. Use or distribution of such technology outside of this product is
prohibited without a license from Microsoft or an authorized Microsoft
subsidiary.
• LDAC™ and LDAC logo are trademarks of Sony Corporation.
• The BLUETOOTH® word mark and logos are registered trademarks owned by
Bluetooth SIG, Inc. and any use of such marks by Sony Corporation is under
license. Other trademarks and trade names are those of their respective owners.
• Android, Google Play, and the Google Play logo are trademarks of Google LLC.
• Apple, iPhone, iPod, and iPod touch are trademarks of Apple Inc., registered in
the U.S. and other countries.
• Use of the Made for Apple badge means that an accessory has been designed
to connect specifically to the Apple product(s) identified in the badge, and has
been certified by the developer to meet Apple performance standards. Apple is
not responsible for the operation of this device or its compliance with safety
and regulatory standards.
• All other trademarks are trademarks of their respective owners.
• In this guide, ™ and ® marks are not specified.
Specifications
Speaker section
Speaker system:
2-way, Bass Reflex
Speaker unit:
Tweeter L/R: 50 mm, horn type
Woofer: 200 mm, cone type
Inputs
AUDIO IN:
Voltage 2 V, impedance 47 kilohms
MIC/GUITAR:
Sensitivity 1 mV, impedance 10 kilohms (when guitar mode is turned off)
Sensitivity 200 mV, impedance 1 Megaohm (when guitar mode is turned on)
Disc player section
System:
Compact disc and digital audio system
Laser Diode Properties
Emission Duration: Continuous
Wavelength: 790 nm
Laser Output*: Less than 44.6 μW
* This output is the value measurement at a distance of 100 mm from the
objective lens surface on the Optical Pick-up Block with 7 mm aperture.
Frequency response:
20 Hz – 20 kHz
USB section
Supported USB device:
Mass Storage Class
Maximum current:
1 A
(USB) port:
Type A
FM tuner section
FM stereo, FM superheterodyne tuner
Antenna:
FM lead antenna (aerial)
Tuning range:
87.5 MHz – 108.0 MHz (50 kHz step)
BLUETOOTH section
Communication system:
BLUETOOTH Standard version 4.2
Output:
BLUETOOTH Standard Power Class 2
Maximum output power:
<9.5 dBm
Maximum number of devices to be registered:
8 devices
Maximum number of simultaneous connection (Multipoint):
3 devices
Maximum communication range:
Line of sight approx. 10 m
Frequency band:
2.4 GHz band (2.4000 GHz – 2.4835 GHz)
Modulation method:
FHSS (Freq Hopping Spread Spectrum)
Compatible BLUETOOTH profiles
A2DP (Advanced Audio Distribution Profile)
AVRCP (Audio Video Remote Control Profile)
Supported codecs:
SBC (Subband Codec)
AAC (Advanced Audio Coding)
LDAC
1) The actual range will vary depending on factors such as obstacles between devices,
magnetic fields around a microwave oven, static electricity, reception sensitivity,
antenna's performance, operating system, software application, etc.
2) BLUETOOTH standard profiles indicate the purpose of BLUETOOTH communication
between devices.
Supported audio formats
Supported bit rate and sampling frequencies:
MP3:
32/44.1/48 kHz, 32 kbps – 320 kbps (VBR)
AAC:
8/11.025/12/16/22.05/24/32/44.1/48 kHz, 8 kbps – 320 kbps (VBR)
WMA:
8/11.025/16/22.05/32/44.1/48 kHz, 48/64/96/128/160/192 kbps (CBR), 64 kbps –
161 kbps (VBR)
WAV:
8/11.025/12/16/22.5/24/32/44.1/48 kHz (16 bit)
General
Power requirements:
AC 120 V – 240 V, 50/60 Hz
Power consumption:
32 W
Power consumption (at the Power Saving mode):
0.5 W (when "BT STBY" is set to "OFF")
2 W* (when "BT STBY" is set to "ON")
Dimensions (W/H/D) (Approx.):
333 mm × 600 mm × 299 mm
Mass (Approx.):
8.1 kg
Operating temperature:
5 °C – 35 °C
* The power consumption of the system will be less than 0.5 W when "BT STBY" is set to
"OFF".
Supplied accessories
Remote control (RMT-AM330U) (DC 3 V) (1)
R03 (DC 1.5 V) (size AAA) batteries (2)
FM lead antenna (aerial) (1)
AC power cord (mains lead) (1)
AC plug adaptor* (1) (supplied only for certain areas)
* This plug adaptor is not for the use in Chile, Paraguay and Uruguay. Use this plug
adaptor in the countries/regions where it is necessary.
Design and specifications are subject to change without notice.
1)
2) :
Compatible iPhone/iPod models
iPhone 11 Pro Max, iPhone 11 Pro, iPhone 11, iPhone XS Max, iPhone XS, iPhone XR,
iPhone X, iPhone 8 Plus, iPhone 8, iPhone 7 Plus, iPhone 7, iPhone SE, iPhone 6s
Plus, iPhone 6s, iPhone 6 Plus, iPhone 6, iPod touch (7th generation), iPod touch
(6th generation)
The system is compatible with iOS 11.0 or later.
Español Equipo de audio para el hogar
Antes de utilizar el sistema, lea esta guía atentamente y consérvela para
consultarla en el futuro.
Nombre del producto: Equipo de audio para el hogar
Modelo: MHC-V13
Tensión nominal: ca 120 V – 240 V
Frecuencia nominal: 50/60 Hz
Potencia nominal: 32 W
POR FAVOR LEA DETALLADAMENTE ESTA GUÍA DE REFERENCIA ANTES DE
CONECTAR Y OPERAR ESTE EQUIPO.
RECUERDE QUE UN MAL USO DE SU APARATO PODRÍA ANULAR LA GARANTÍA.
AVISO IMPORTANTE PARA MÉXICO
La operación de este equipo está sujeta a las siguientes dos condiciones: (1) es
posible que este equipo o dispositivo no cause interferencia perjudicial y (2) este
equipo o dispositivo debe aceptar cualquier interferencia, incluyendo la que
pueda causar su operación no deseada.
Para consultar la información relacionada al número del certificado, refiérase a la
etiqueta del empaque y/o del producto.
Nota:
Este producto utiliza el módulo para funcionalidades inalámbricas:
Marca: Sunitec
Modelo: BM64C2
ADVERTENCIA
Para reducir el riesgo de incendios, no cubra las aberturas de ventilación del
aparato con periódicos, manteles, cortinas, etc.
No exponga el aparato a fuentes con llama descubierta (por ejemplo, velas
encendidas).
Para reducir el riesgo de incendios o descargas eléctricas, no exponga el aparato
a goteos o salpicaduras, ni coloque recipientes con líquidos, como jarrones,
encima de éste.
Puesto que el enchufe principal se utiliza para desconectar la unidad de la
corriente, conecte la unidad a una toma de corriente de ca de fácil acceso. En
caso de observar un funcionamiento anómalo de la unidad, desconecte
inmediatamente el enchufe principal de la toma de corriente de ca.
No instale el aparato en un espacio cerrado, como una estantería para libros o un
armario empotrado.
Aunque se haya apagado la unidad, esta continuará recibiendo suministro
eléctrico mientras esté conectada a la toma de corriente de ca.
Solo para uso en interiores.
La siguiente información solo es válida para los equipos que se
comercializan en países/regiones que cumplan con la
Normativa sobre Compatibilidad Electromagnética (EMC).
Este equipo se ha probado y ha demostrado cumplir con los límites establecidos
en la Normativa sobre Compatibilidad Electromagnética (EMC) cuando se utiliza
un cable de conexión de una longitud inferior a 3 metros.
PRECAUCIÓN
Existe riesgo de explosión si la pila se reemplaza por pilas de distinto tipo.
No exponga las pilas o aparatos con pilas instaladas a fuentes de calor excesivo,
como la luz solar y fuego.
PRECAUCIÓN
Precaución – el uso de controles o ajustes o el rendimiento de procedimientos
distintos de los especificados en el presente documento pueden resultar en una
peligrosa exposición a radiaciones.
Este aparato está clasificado como producto láser de clase 1 según la norma IEC
60825-1:2014.
No poner este producto cerca de aparatos médicos
Este producto (incluyendo los accesorios) tiene un imán (o imanes) que puede
interferir con marcapasos, válvulas de derivación programables para el
tratamiento de la hidrocefalia, o con otros aparatos médicos. No ponga el
producto cerca de personas que utilicen dichos aparatos médicos. Consulte con
su médico antes de utilizar este producto si utiliza cualquiera de dichos aparatos
médicos.
Solución de problemas
Si el código de error aparece en el visor
En la siguiente tabla puede consultar la acción correctiva.
Código de Acción correctiva
error
"PT S0" / Desenchufe inmediatamente el cable de alimentación de ca y
"PT S5" / compruebe si algún objeto está obstruyendo los orificios de
"PT S6" / ventilación de la unidad. Si tras realizar las comprobaciones
"PT T0" / necesarias no se ha detectado ningún problema, vuelva a
"PT T5" / conectar el cable de alimentación de ca y encienda el sistema.
"PT T6" Si el problema continúa, póngase en contacto con el
distribuidor de Sony más cercano.
"PT SX" / Póngase en contacto con el distribuidor Sony más cercano.
"PT TX"
("X" es un
número distinto
de 5 y 6)
Precauciones
Cuando transporte la unidad
Para evitar que el mecanismo del disco se averíe, realice el siguiente
procedimiento antes de transportar la unidad.
Utilice los controles de la unidad para realizar esta operación.
1
Extraiga el disco.
Pulse PUSH OPEN/CLOSE para abrir y cerrar la bandeja de discos.
2
Pulse  para apagar el sistema.
3
Una vez que desaparezca el "STANDBY", desenchufe el cable de
alimentación de ca.
Notas sobre discos
• Antes de reproducirlos, limpie el disco con un trapo desde el centro hacia el borde.
• No limpie discos con disolventes, como diluyente o limpiadores disponibles en
el mercado o spray antiestático para LP de vinilo.
• No exponga los discos a la luz directa del sol o fuentes de calor como
conductos de aire caliente, ni los deje en el interior de un coche aparcado a la
luz directa del sol.
Seguridad
• Desconecte el cable de alimentación de ca de la toma de corriente de la pared
si no va a utilizar el sistema durante un periodo largo de tiempo. Cuando
desenchufe el sistema, hágalo siempre agarrando el enchufe. Nunca tire del cable.
• Si cae dentro del sistema algún objeto sólido o líquido, desenchúfelo y deje que
personal calificado lo compruebe antes de utilizarlo de nuevo.
• El cable de alimentación de ca debe ser sustituido únicamente en un taller de
servicio calificado.
Sobre el manejo del sistema
• Este sistema no es resistente al agua ni a prueba de goteo. Evite todo contacto
del sistema con el agua; asegúrese de no limpiarlo con agua.
• No deje abierta la bandeja de discos si no va a utilizarla. Podría entrar polvo y
provocar un mal funcionamiento.
Colocación
• No coloque el sistema en una posición inclinada o en ubicaciones
extremadamente calientes, frías, polvorientas, sucias, húmedas o sin ventilación
adecuada, o sujetas a vibración, luz directa del sol o luz intensa.
• Tenga cuidado si coloca el sistema sobre superficies que tengan un tratamiento
especial (por ejemplo, ceras, aceites, abrillantador), ya que pueden aparecer
manchas o producir decoloración en la superficie.
• Si el sistema se traslada directamente desde una ubicación fría a una caliente o
si se coloca en una habitación muy húmeda, la humedad se puede condensar
en la lente del interior de la unidad y producir fallos de funcionamiento. En esta
situación extraiga el disco y deje el sistema encendido cerca de una hora hasta
que la humedad de evapore.
Acumulación de calor
• La acumulación de calor en la unidad durante su funcionamiento es normal y
no debe ser causa de alarma.
• No toque el gabinete si se ha usado de manera continuada a un volumen alto,
ya que el gabinete puede haberse calentado mucho.
• No obstruya los orificios de ventilación.
El sistema de altavoces
El sistema de altavoces no está magnéticamente apantallado y la imagen de los
televisores del entorno pueden distorsionarse magnéticamente. En esta situación,
apague el televisor, espere entre 15 y 30 minutos y enciéndalo de nuevo. Si no
hay mejoría, aleje el sistema del televisor.
Limpieza del gabinete
Limpie el sistema con un paño suave humedecido ligeramente con una solución
de detergente suave.
No utilice ningún tipo de estropajos abrasivos, polvo desengrasante ni
disolventes, como diluyente, bencina o alcohol.
Acerca de la comunicación BLUETOOTH®
• Los dispositivos BLUETOOTH deben usarse aproximadamente a una distancia
de 10 metros (separación libre de obstáculos). El alcance de comunicación
efectiva puede ser menor en las siguientes condiciones:
– Cuando una persona, objeto metálico, pared u otros obstáculos se encuentra
entre los dispositivos conectados mediante BLUETOOTH.
– Lugares donde hay instalada una red LAN inalámbrica.
– Cerca de hornos microondas en funcionamiento.
– Lugares donde se producen otras ondas electromagnéticas.
• Los dispositivos BLUETOOTH y el equipo LAN inalámbrico (IEEE 802.11b/g/n)
utilizan la misma banda de frecuencia (2,4 GHz). Cuando utilice un dispositivo
BLUETOOTH cerca de un dispositivo equipado con la función LAN inalámbrica,
pueden producirse interferencias electromagnéticas. Esto puede provocar una
reducción de la velocidad de transferencia de los datos, ruido o la imposibilidad
de conectarse. Si esto sucediera, intente lo siguiente:
– Utilice este sistema a una distancia mínima de 10 metros del equipo LAN
inalámbrico.
– Apague el equipo LAN inalámbrico cuando utilice su dispositivo BLUETOOTH a
menos de 10 metros.