Rotel RTC-950AX Owner's Manual page 6

Therefore the tone controls do not function, but this unit
provides superior tone quality if the listening room acous¬
tics are extremely lively or dead and the required compen¬
sations when adjusts by reallocating the furnitures, or the
speakers etc., are failed. Set the selector to ON, and
adjusts the tone with the tone controls.
(19) Tone Controls
The BASS control regulates the low frequencies and the
TREBLE control regulates the high frequencies. The center
points are for the flat frequency response. Turn clockwise
to boost the response and counterclockwise to reduce it.
(20) Headphones Jack
For monitoring, plug your headphones into this jack. The
volume of the headphone sound can be regulated with the
volume control.
tuner to increase or decrease, depending on which end of
the Tuning button pressed, the received frequency until a
reasonably strong signal is received. At this point the
tuning will stop automatically.
In the manual mode, pressing either end of Tuning button
causes the tuner to increase or decrease the received
frequency only for as long as the Button is depressed.
NOTE: Auto tuning does not operate for AM (Both MW and
LW) band.
(12) Mute Off/ Mono Button
Allows selection of FM mono or stereo operation. When
the Mono position is chosen, any broadcast will be
received monaurally and the muting switch for suppress¬
ing interstation noise will be deactivated to pull weak
signals which are normally cut off during the stereo opera -
tion. For reception of weak and noisy signals, use the Mute
Off/ Mono position. For normal use, choose the stereo
operation by deactivating the Button. In this position,
stereo broadcasts will be provided in stereo and the
STEREO indicator will light up. When mono programs are
broadcasted, mono sound is provided and the STEREO
indicator will not light.
(13) Band Selection Button
Allows to select reception on FM or AM band (MW or LW
in case of the tuner with both MW and LW).
(14) Audio Muting Button
Pressing the button will immediately cause a large reduc¬
tion in volume level of sound, and pressing it again to
restore the previous one.
This button is most useful when you wish a temporary
period of quieter sound. When audio muting is in operation,
the LED indicator on it lights up.
(15) Function Selector Button
Allows to choose any input source connected to the unit
you wish to listen to.
TAPE- When playing the connected Cassette Tape Deck.
AUX- When playing the connected Video Cassette Re¬
corder, Video Disc Player and or other auxiliary com¬
ponents.
CD- When playing the Compact Disc Player.
PHONO-When playing the connected Turntable.
TUNER- When listening to FM or AM,(MW or LW in case
of Tuner with both MW and LW) band.
When the desired source program is in operation, the LED
indicator on the function button will light up.
(16) TAPE Selector Button
To select the tape position 1 or 2 on the selector control,
depending on the Cassette Tape Deck you wish to play is
connected on Tape 1 orTape 2 terminals on the rear panel.
(17) Balance Control
Set normally at the center position for equal volume level
from both speakers. Turning to the right decreases the
sound from the left speakers, and turning to the left
decreases the sound from the right speakers. Use the
control only when there is an unbalance in the sound level
between the two speakers.
(18) Tone Control Selector
With the selector at OFF, the signals do not pass through
the tone control circuit (in order to prevent deterioration of
tone quality).
POWER
-CD
PHONO TUNER CD AUX
- CD CD CD CD
TAPE Iffiaavs
M W~
- CD CD CD
CD CD CD CD
~*e bSnv
< TUNING >
CD CD CD CD
MUTE <V0LUME >
CD CD CD
STOP PAUSE -JIBSK PLAY
• CD CD iiSSCD
M
SEARCH* M TRACK 1*1
CD CD CD CD
SCAN RANDOM PROGRAM
CD CD CD
CD CD CD CD
9 0 REPEAT
CD CD CD
Remote Control Function
(21) Power Button for on/off.
(22) Function Selector Buttons (same as item 15).
(23) Cassette Control Buttons- Permit you to remote con¬
trol Rotel's RD-965BX or RD-955AX cassette deck
connected to the REMOTE socket on the rear panel.
Press
*
◄ button to rewind tape.
Press ►
button to play back tape.
Press ► ► button to advance tape rapidly forward.
Press 11 button for temporary suspension of tape
motion during recording or playback. Pressing the