Related Manuals for TECshow THUNDERSTROBE
Summary of Contents for TECshow THUNDERSTROBE
- Page 1 THUNDERSTROBE INDOOR LED MOVING STROBE USER MANUAL PLEASE READ THE INSTRUCTIONS CAREFULLY BEFORE USE P. 1 Versión Español | Tecshow NEBULA PAR 162 II...
-
Page 2: Specifications
DMX channels: 15/43CH • Operational modes: DMX512, self-propelled, master-slave, voice control, with RDM function. • Sections control: RGB / 8 sections / cold white 8 sections. • Dimming: 32bit 0~100% linear dimming • P. 2 English Version | TECSHOW Thunderstrobe... -
Page 3: Safety Instructions
10 minutes before opening the fixture genuine RUSH. or removing the lamp. • Never attempt to bypass the fuse. Always replace defective fuses with ones of the specified type and rating. P. 3 English Version | TECSHOW Thunderstrobe... -
Page 4: Menu Function
Modify the middle white light bead brightness (W000~W255) up and W255 B000 down to save the confirmation key. Display temperature, such as T045 indicates that the current lamp tem- T000 perature is 45 °C; 10K thermistor is not installed, display T000. P. 4 English Version | TECSHOW Thunderstrobe... -
Page 5: Factory Settings
Send the factory set parameters up or down to all other lamps con- nected by three-core signal lines; confirm the sending parameters to S end S end press the menu key for 5 seconds, and press the confirmation key to cancel the sending. P. 5 English Version | TECSHOW Thunderstrobe... -
Page 6: Dmx Channels
White light total dimming 000-255 White light flash 000-255 White light mode (see: VI. Mode effect for details) 000-255 White light mode speed 000-255 White light bead linear dimming 0-250 Of no avail 251-255 Reset P. 6 English Version | TECSHOW Thunderstrobe... - Page 7 Paragraph 3: linear dimming of white light beads 000-255 Paragraph 4 000-255 Paragraph 5 000-255 Paragraph 6 white light beads 000-255 Paragraph 7 white light beads 000-255 Paragraph 8 white light beads 000-255 000-250 Of no avail 251-255 Reset P. 7 English Version | TECSHOW Thunderstrobe...
- Page 8 Two section of green and blue dyed light horse racing. 75-77 Two sections of red, green and blue dyeing light horse racing. 78-80 Integrated mode code number 19-25 cycle. 81-83 A piece of red light beads to refresh. P. 8 English Version | TECSHOW Thunderstrobe...
- Page 9 A section of red and green staining light and a section of red and 162-164 blue dyeing light ran around. A red and blue stained lamp and a green and blue stained lamp 165-167 will run around. P. 9 English Version | TECSHOW Thunderstrobe...
- Page 10 A section of red, green and blue stained lights accumulates. 246-248 Integrated mode code number 113- 119 cycle. 249-251 Colorful accumulation. 252-254 Colorful flow. Mode code Mode code 11~81, can push and pull RGB to change the background color. P. 10 English Version | TECSHOW Thunderstrobe...
- Page 11 150-155 Each section of white light at both ends refreshes in the middle. 156-161 The middle white light is refreshed at both ends 162-167 Each section of white light runs back and forth. P. 11 English Version | TECSHOW Thunderstrobe...
- Page 12 A gradual white light moves from left to right and finally shines 228-233 back on. 234-239 Two white light pendulum. After a section of white light accumulates, another section 240-245 disappears. 246-251 The white light collided and grows at both ends. 252-255 Aggregative model. P. 12 English Version | TECSHOW Thunderstrobe...
- Page 13 n e o . a m p r o w e b . c o m /am progro up /amprogro up...
Need help?
Do you have a question about the THUNDERSTROBE and is the answer not in the manual?
Questions and answers