HP 2641A Reference Manual page 202

Line Set installation 7-7
Line strap 5-10, 5-13
locate end-of-data 4-2
logic levels 7-26
Lower Case ROM installation 7-6
LRC 5-26
Main Channel protocol 5-16
margins 2-4
Math Character Set " " 2-10
Math Set installation " 7-7
medium, copying to the end of a 4-5
memory configuration 7-10
memory lock 2-4
message blocks 5-25
modem disconnect command 3-5
modems 5-1, 5-6
Monitor Mode 5-16, 5-47
moving text blocks 2-6
multicharacter transfers (block) 5-25
multicharacter transfers (point-to-point) 5-8
multipoint 5-36
multipoint communications 5-1
multipoint example A-I
NAK 5-30
networks 5-1
next page 2-4
no test 7-43
Null characters 5-7
numeric field checking " 2-7
opening the terminal 7-2
options and accessories B-7, B-12, B-17
output buffer (communications) 5-27
PAD 5-31
PA key 5-36
page 2-4
Page strap 5-10, 5-13
Parity Switch (block) 5-35
Parity switch (point-to-point) 5-4
PF key " .. '" . 5-36
point-to-point 5-6
point-to-point configuration 5-16
polling 5-39
positioning the cursor 2-2
Power Down Protect Cable 7-29
power supply adjustment " 7-17
primary terminal status , , 6-2
printer installation (9866) 7-13
printer installation (9871) 7-17
printer selection 4-2
printer status 6-7
programmable keys 3-3
Programmers Reference Table B-2, B-9, B-14
programming Keyboard Interface switches 3-1
programming the latching keys 3-1
programming the soft keys 3-3
program load command 3-5
protected fields 2-7
protocol, block 5-25
protocol, Main Channel 5-16
protocol, Reverse Channel 5-16
protocols 5-6
RAM error 7-39
range switch 5-4
read, binary 4-5
read control byte 4-1
record copy 4-4
recording file marks 4-2
record transmission 4-3
Remote key 5-4
reset terminal (full) 3-5
reset terminal (soft) 3-5
rethreading tapes D-l
retransmit last record 4-1
return. " " .. '" 2-3
Reverse Channel protocol 5-16
rewind " 4-2
roll down 2-4
roll up 2-4
ROM error. '" 7-39
RS232C signals 7-27
RVI 5-31
Scale switch 5-4
secondary terminal status 6-4
selection, device 4-2
selection, device function 4-2
selection (multipoint) 5-40
selection of character sets 2-9
Self-Test command 3-5
Self-Test procedure 7-39
send byte CoUllt 4-1
send display 3-5
sensing the cursor position 2-2
set tab " 2-4
signal levels 7-31
signal line control 5-12, 5-16
signals, interface 5-3, 7-26
soft key labels 3-4
soft key programming 3-3
soft reset 3-5
specifications B-8, B-13, B-18
speed switches (block) 5-35
status 6-1
status, block configuration 5-41
status, device 6-6
status interpretation 6-1
status, terminal 6-1
strap options (block) 5-26
strapping option selection 7-18
STX " 5-16, 5-30
switch settings 5-4
SYN 5-31
synchronous compatibility (block) 5-29
Syncrhonous Multipoint Interface 7-25
1-3