Table of Contents
Advertisement
Installation
Table 7-2. 13232 Cable Assemblies (Continued)
CONNECTORS
CABLE
FUNCTION
A
B
C
LENGTH
HOOKUP
13232R
Provides 100-foot exten-
Multipoint
Multipoint
Multipoint
30.5 Metres
-~
~
sion to 13232P, Q, T,
(male)
(female)
(female)
100 feet
multipoint cables. (Cable
0"
part no. 02640-60134.)
132~QmT ~A13232RK~
13232P.
0
or T
132328
Connects 13238A Duplex
9866
Hood
-
1.83 Metres
~
Register PCA to 9866A/B
printer
6 feet
I
~
Printer. (Cable part no.
(male)
9866A/B
13232S
02640-60135.)
PRINTER
13232T
Provides power-down
Multipoint
Hood
Multipoint
4.57 Metres
13232T&
protection for a terminal
(male)
(female)
15 feet
TO
A
in multipoint configura-
(each leg)
TERMINAL
ijl
tion. (Cable part no.
UPSTREAM
02640-60151.)
TO
TERMINAL
DOWNSTREAM
13232U
Provides direct connec-
RS232C
RS232C
-
1.52 Metres
~
tion to a computer by re-
(female)
(female)
5 feet
A
B
placing the modem con-
a:;
13232U
r\r'L-~.
nections. (Cable part no.
\
,I
u
5060-2403.)
13232N
HP 13234A (4K) TERMINAL MEMORY
MODULE
Install the HP 13234A
(+
4K) memory accessory as
follows:
1. ()
Open terminal to its half open position (refer to
page "Opening the Terminal").
2. ()
Locate and ensure that the Control Memory PCA,
part no. 02640-60192, has all jumpers installed.
(See figures 7-2 and 7-8.) For HP 2641A, refer to
figure 7-36 for second Control Memory PCA
jumper configuration.
3. ()
Using figure 7-9 as a guide, locate memory
jumpers on 4K Memory PCA.
4. ()
Using figures 7-10 and 7-11 as guides, arrange
PCA starting address jumpers to select
appropriate memory starting address for the size
memory being configured. For example: to
configure an 8K memory, remove all jumpers
from one of the 4K Memory PCAs, and remove all
but the 4K jumper from the other 4K Memory
PCA.
7-10
NOTE
If a full 16K of memory is to be config-
ured, the 4K block of data comm buffer is
located outside the zero to 12K of display
memory space.
5. ()
Install memory PCA's in any vacant Backplane
Assembly connectors ensuring that no connectors
are left vacant between any PCA's other than the
two cartridge tape unit PCA's (if installed).
6. ()
Check and, if necessary, adjust power supply
(refer to ((Power Supply Adjustment").
7. ()
Firmly grasp mainframe top cover in one hand
and release safety latch by pressing it inboard
with other hand. Then, using both hands,
carefully lower top cover to its closed position.
HP 13236B CARTRIDGE TAPE UNIT
The HP 13236B Cartridge Tape Unit is provided to up-
grade the terminals to include mass storage capabilities.
This accessory consists of two cartridge tape (CTU) Trans-
port Assemblies, two Tape Cartridges, a CTU Interface
PCA, a Read/Write PCA, a CTU Top Plane Assembly, a
Motor Cable Assembly, a front bezel and required attach-
ing hardware. Installation procedures are contained in the
HP 13236A!B Cartridge Tape Unit Accessory Manual,
part no. 13236-90001.
Advertisement
Table of Contents
