In Case Of Difficulty; Specifications - Kenwood DP-M6650 Instruction Manual

In case of difficulty
What appears to be a malfunction may not always be serious. If your unit should not perform as expected, consult the
table below to see if the problem can be corrected before seeking help from your dealer or service representative.
Symptom Cause
Remedy
No power is applied with the POWER
switch ON.
• Power plug is loosely connected.
• With the power plug connected to the
switched AC outlet of an amplifier, the
power of the amplifier is turned off.
• Insert the power plug firmly into the AC
outlet.
• Turn the amplifier's power ON.
Disc is loaded, player does not play. • Disc is loaded upside down.
• Disc is loose.
• Disc is dirty.
• Disc is cracked.
• Condensation occured on the optical lens
unit.
• Load the disc again with its label side up.
• Insert the disc properly.
• Wipe off the dust on the surface of the
disc referring to "Disc handling precau¬
tions".
• Replace the disc with a new one.
• Leave the player for about 1 hour so that
the condensation is removed.
No sound.
• Disc is not loaded.
• Play mode is not entered (The play/pause
indicator is not lit.)
• Disc is too dirty.
• Disc is cracked.
• The connection cords are inserted loosely.
• Load a disc.
• Press the (►/Til key.
• Wipe off the dust on the disc surface
referring to "Disc handling precautions".
• Replace the disc with a new one.
• Connect all connection cords firmly.
Music is interrupted. (Sound is skipped.) • Disc is too dirty.
• Disc is cracked.
• Oscillation is applied to this unit.
• Wipe off the dust on the disc surface
referring to "Disc handling precautions".
• Replace the disc with a new one.
• Try selecting a place where no strong
vibrations occur by changing the installa¬
tion place, etc.
Play begins as soon as the power is
turned on.
• This unit is designed so that play begins
automatically when the power is turned on
if a disc or a magazine is already loaded.
• If automatic play is not required, remove
the disc or the magazine from the player
before turning the power OFF.
Notes:
1. This system is microprocessor-controlled, so malfunction may occur due to external noise or interference noise. In such a case, unplug the power
cord, plug it and turn power on again.
2. Do not usecontact cleaners because it couldcausea malfunction. Be specially careful against contact cleaners containing oil, forthey may deform
the plastic components.
Specifications
[Format]
System.Compact disc digital audio system
Laser.Semiconductor laser
Number of channels.2 channels
playing rotation ... 200 rpm - 500 rpm (CLV)
[D/A Converters]
D/A conversion..
Oversampling.
[Audio]
Frequency response.
Signal to noise ratio.
Dynamic range.
Total harmonic distortion
1 Bit
. 8 fs
..8 Hz ~ 20 kHz ± 1.0 dB
.. More than 96 dB
. More than 94 dB
Less than 0.005% {at 1 kHz)
Channel separation.More than 90 dB (at 1 kHz)
Wow
&
flutter....Unmeasurable limit
Output level/impedance
Fixed.2.0 V/3.3 kO
Headphones output (max.).20 mW/16 £}
(DP-M6650 only)
[General]
Power consumption.. 15 W
Dimensions...W: 440 mm (17-5/16")
H: 128 mm (5-1/16")
D: 368 mm (14-1/2")
Weight (net).5.4 kg (11.9 lb)
Note:
KENWOOD follows a policy of continuous advancements in development. For this reason specifications may be changed without notice.
24
DP-M6650/DP-M5550 {En>