Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for GBD SNAPPER 250
Summary of Contents for GBD SNAPPER 250
- Page 1 SNAPPER SNAPPER 250 Electromechanical gearmotor INSTRUCTIONS FOR INSTALLATION...
-
Page 2: Typical Installation
SNAPPER TYPICAL INSTALLATION M2 Slave M1 MASTER RIGHT OPERATOR-MOTOR 2 LEFT OPERATOR-MOTOR 1 OPERATOR DIMENSIONS... - Page 3 SNAPPER PARTS Straight arm 1pce Curved arm 1pce U-shaped fixing plate 1pce Mechanical stopper 2pcs Front-end fixing bracket 1pce M6 Screws 4pcs M10 nuts 2pcs M8 cup square screws 2pcs M10 Washer 2pcs M8 Shoulder screw 2pcs M6 spring washer 4pcs M8 nut 4pcs...
-
Page 4: Installation Dimensions
SNAPPER INSTALLATION DIMENSIONS unit: mm 90° OPERATOR INSTALLATION 6 mm... - Page 5 SNAPPER OPERATOR INSTALLATION...
- Page 6 SNAPPER OPERATOR INSTALLATION UNLOCK MANEUVRE...
-
Page 7: Electrical Connections
SNAPPER ELECTRICAL CONNECTIONS MEMO LEARN BE24 DIP3 DIP4 DIP2 DIP1 PHASE NEUTRAL 230Vac OVERCURRENT CIRCUIT BREAKER RESIDUAL-CURRENT DEVICE F4 F2A PHASE NEUTRAL YELLOW/GREEN WIRE... - Page 8 SNAPPER WIRING WITH ENCODER LEFT OPERATOR-MOTOR 1 RIGHT OPERATOR-MOTOR 2 BLACK WIRE WHITE WIRE RED WIRE WHITE WIRE 18AWG YELLOW WIRE RED WIRE WHITE WIRE BLACK WIRE MEMO LEARN BE24 DIP3 DIP4...
- Page 9 SNAPPER WIRING WITHOUT ENCODER LEFT OPERATOR-MOTOR 1 RIGHT OPERATOR-MOTOR 2 YELLOW WIRE WHITE WIRE 18AWG MEMO LEARN BE24 DIP3 DIP4...
- Page 10 SNAPPER ELECTRIC LOCK INSTALLATION...
-
Page 11: Backup Batteries
SNAPPER BACKUP BATTERIES BE24 1 . 3... -
Page 12: Warnings For The Installer
SNAPPER INTRODUCTION The SNAPPER 250 operator for swing gates is an electromechanical device that transmits motion to the gate by means of an articulated arm. It is locked when the motor is not running, it is necessary to install locks... -
Page 13: Warnings For The User
SNAPPER WARNINGS FOR THE USER • In the event of an operating fault or failure, cut the power upstream of the control unit and call Technical Service. • Periodically check functioning of the safety devices. Any repairs must be carried out by specialised personnel using original and certified materials. -
Page 14: Technical Data
SNAPPER TECHNICAL DATA Operator SNAPPER 250 Type Irreversible electromechanical with worm screw Supply voltage 230Vac Power absorbed 100 W (~1000 N) Electric motor 24 Vdc Max torque 250Nm 2.5 m Maximum leaf length If fitted on blind/flush panel doors it is mandatory to use an electric lock... -
Page 15: Preliminary Warnings
SNAPPER PRELIMINARY WARNINGS Check that the gate structure is in conformity with the regulations in force and that the gate movement is linear without friction. Preliminary checks: • Check that the gate structure is sufficiently robust. • In any event, the actuator must push the leaf at a reinforced point. •... -
Page 16: Maintenance
SNAPPER UNLOCKING DEVICE If the gate needs to be operated manually because of a power failure or operator malfunctioning: Insert the release key to the release slot fig. 7 . Ÿ Turn the release key . Ÿ Pull out the release bar and keep it pulled out . Ÿ... - Page 17 CE Declaration of conformity The manufacturer: GI.BI.DI. S.r.l. Via Abetone Brennero, 177/B, 46025 Poggio Rusco (MN) - ITALY declares that the products: ELECTROMECHANICAL GEARMOTOR SNAPPER 250 are in conformity with the following CEE Directives: Directive 2006/95/CE and subsequent amendments; • •...
- Page 18 GI.BI.DI. S.r.l. Via Abetone Brennero, 177/B 46025 Poggio Rusco (MN) - ITALY Tel. +39.0386.52.20.11 Fax +39.0386.52.20.31 E-mail: info@gibidi.com Numero Verde: 800.290156 w w w . g i b i d i . c o m...