Subscribe to Our Youtube Channel
Related Manuals for Inaxsys STORM INSDO4IRWA
Summary of Contents for Inaxsys STORM INSDO4IRWA
- Page 1 INSDO4IRWA 4.1MP HD IP Dome Camera with Autofocus and IR Quick Start Guide Version 1.0.0...
- Page 2 Welcome Thank you for purchasing our Network camera! This user’s manual is designed to be a reference tool for your system. Please read the following safeguard and warnings carefully before you use this series product! Please keep this user’s manual well for future reference! Important Safeguards and Warnings 1．Electrical safety All installation and operation here should conform to your local electrical safety codes.
- Page 3 Please do not dismantle the device; there is no component which can be fixed by users themselves in the machine. It may cause water leakage or bad image for the device due to unprofessional dismantling. It is recommended to use the device with thunder proof device in order to improve thunder proof effect. The grounding holes of the product are recommended to be grounded to further enhance the reliability of the camera.
- Page 4 Please refer to the disk for more details, check and download corresponding user’s manual and tool. Before installation, please open the package and check all the components are included. Contact your local retailer ASAP if something is broken in your package. Accessory Name Amount Network Camera Unit...
-
Page 5: Table Of Contents
Table of Contents Structure ............................. 1 Port Description ......................1 Framework and Dimension ..................2 Bidirectional Talk ......................2 1.3.1 Device-end to PC-end ..................2 1.3.2 PC-end to the Device-end ..................2 Alarm Setup ........................2 Device Installation ........................5 Installation Steps ...................... -
Page 6: Structure
1 Structure Note: The following figure is for reference only, which is used to know the functions of device external ports. There are differences about external ports for some product models, please refer to the actual object for more details. 1.1 Port Description You can refer to the following figure for more details. -
Page 7: Framework And Dimension
Connect to standard Ethernet Network port Support POE function 1.2 Framework and Dimension Note: The following figures are for reference only, which are used to know the device dimension, please refer to the actual product for more details. Please refer to the following figure for dimension information. - Page 8 Note: It is only supported by some series products. Figure 1-3 Alarm input, output description: Step 1 Connect alarm input device to the alarm input of I/O cable. Step 2 Connect alarm output device to the alarm output of I/O cable, alarm output is collector open circuit output which connects 10K resistor to 3.3V externally.
- Page 9 Figure 1-5 Figure 1-6 Mode A: Level application. Alarm output high and low level, alarm output is OC; it needs to increase pull-up resistance externally to work normally. Max external pull-up level is 5V, max port current is 5mA. After external pull-up resistance is increased, the default of output signal is high level (external pull-up voltage), and it switches to low level when there is alarm output (when the working current is 5mA, output voltage is less than 0.8V).
-
Page 10: Device Installation
2 Device Installation 2.1 Installation Steps Figure 2-1 Important Before the installation, please make sure the installation surface can at least support 3x weight of the camera and the bracket. Please follow the steps listed below to install the device. Please refer to 错误！未找到引用源。1 for reference. - Page 11 tighten the locking screws on both sides; Hold the IR light decoration cover to rotate horizontally, adjust the image and adjust the lens horizontal direction to the targeted location; Range of adjusting lens angle: vertical (0°～+65°), horizontal (0°～+355°). Figure 2-2 Step 6 Take up the dome enclosure;...
-
Page 12: Micro Sd Card Installation
Connect the pin accessed with cable to the device, then install the device according to the normal steps. 2.2 Micro SD Card Installation Note: Some series products do not support the Micro SD card storage function, which can’t be applied to the following chapter. -
Page 13: Network Configuration
3 Network Configuration The IP address of all the cameras is the same when leaving factory (default IP192.168.1.108), in order to make the camera get access to the network smoothly, please plan the useable IP segment reasonably according to the actual network environment. 3.1 Modify IP Address IP address can be acquired and modified through quick configuration tool for the cameras which are accessed via wired network, it needs to connect wired network to configure wireless parameters... -
Page 14: Login Web Interface
Figure 3-1 Step 3 Modify the camera IP address on the “Net” interface, click “Save” to finish modification. See Figure 3-2 for more details. Figure 3-2 3.2 Login WEB Interface Note: Different devices may have different WEB interfaces, the figures below are just for reference, please refer to the document <<WEB Operation Manual>>... - Page 15 Figure 3-3 Step 3 Install controls according to the system prompt; see Figure 3-4 for the WEB main interface. Please modify the administrator password as soon as possible after you successfully logged in. Figure 3-4...
- Page 16 Note This user’s manual is for reference only. Slight difference may be found in user interface. All the designs and software here are subject to change without prior written notice. All trademarks and registered trademarks mentioned are the properties of their respective owners.
Need help?
Do you have a question about the STORM INSDO4IRWA and is the answer not in the manual?
Questions and answers