Advertisement
Solar panel | 6.5W, 10 year life span |
Battery | 44.4 Wh, 3.7V, Li-ion |
LED count | 60 |
Brightness (Lumens) | Up to 3000 lm |
Recharge time | 10 hours bright sunlight |
Lighting time | Up to 10 nights (Dim lighting mode) |
PIR sensor | 16–26 ft (5~8 m), 120° |
Waterproof | IP65 |
Install height | 8–11 ft (2.5~3.5 m) |
Materials | Poly-carbonate |
Size | 15.0 × 9.7 × 5.5 inches |
Working temperature | 32–113°F (0–45°C) |
Warranty | 1 year |
Suitable for outdoor wall or pole installation in plazas, parks, gardens, courtyards, streets, walkways, pathways, campuses, airfields, farms, and perimeter security.
Activate the light by pressing the button on the underside of the light for 3 seconds. To deactivate, press and hold the button for 3 seconds. Otherwise, use the remote control to switch it on or off.
As the above image shows: Take out the bolts and washers from the accessories bag for pole installation and attach the light to the pole with the U-bolts.
Drill 4 holes in the wall that match the holes in the mounting plate and insert the expansion bolts. Place the washers on the bolt as indicated and tighten the nuts to secure the light to the wall.
Please install the solar light in a place without any shade and facing direct sunlight for better charging.
By default the light is off during the day and comes on automatically at night.
Without programming, it operates in motion detection mode M1 (described later).
The remote control uses 2 AAA batteries (not included)
ON: Turns on the light. When the light is turned on for the first time, the default lighting mode is motion detection mode M1.
OFF: Turns off the light and saves the last lighting mode.
If the light is manually turned off one night, it will not come on the next night automatically. The ON button will need to be pressed in order for the light to come on.
There are 2 main modes the light can be operated in: Motion Detection & Timer mode.
First 5 Hours | After 5 hours | ||||
Mode | Indicator LED color | Standby | Motion Detection* | Standby | Motion Detection* |
M1 | red | None | |||
M2 | green | None | |||
M3 | orange |
* 30 seconds after motion ceases, the light will dim to standby level
To temporarily override the motion detection mode, press the T button on the remote control. When in this mode, the light will run at 100% brightness for 1 or 2 hours and then return to the last programmed mode (M1, M2 or M3).
Brightness | Short Press "T" Button | Indicator LED** | |
1 hour | 100% | once | red flash |
2 hours | 100% | twice | green flash |
** LED flashes for 5 seconds
Green | >70% |
Orange | 30%-70% |
Red | <30% |
A.L.T. - Adaptive Lighting Technology uses smart battery optimization during cloudy days to extend the runtime up to 10 nights. When the battery charge gets low, such as when the days are cloudy and charging is not optimal, the light output may decrease slightly to extend runtime.
The light will remember the last button/program pressed and revert to that setting the following nights until a new program is set.
Floodlight
Remote control
Mounting plate with screws
2 × U-bolts with nuts and washers
4 × Expansion Bolts with nuts and washers
Here you can download full pdf version of manual, it may contain additional safety instructions, warranty information, FCC rules, etc.
Download WAGAN Tech 8591 - Solar + LED Floodlight 3000 Manual
Advertisement
Thank you! Your question has been received!
Need Assistance?
Do you have a question about the 8591 that isn't answered in the manual? Leave your question here.