Limited Warranty Warranty The GSI Group, LLC. (“GSI”) warrants products which it manufactures to be free of defects in materials and workmanship under normal usage and conditions for a period of 12 months after sale to the original end-user or if a foreign sale, 14 months from arrival at port of discharge, whichever is earlier.
Page 4
GENERAL HAZARD WARNING Failure to comply with precautions and instructions provided with this heater can result in death, serious bodily injury and property loss or damage from hazards of fire, explosion, burn, asphyxiation, carbon monoxide poisoning, and/or electrical shock. If you need assistance or heater information such as an instruction manual, labels, etc.
Warnings and Cautions WARNING When Heater Is Connected To Remote Thermostat Heater May Start At Any Time! ELECTRICAL GROUNDING INSTRUCTIONS This appliance is equipped with a three prong (grounding) plug for your protection against electrical shock and should be plugged directly into a properly grounded three-prong receptacle.
93.15 MJ/m ) and natural gas (1075 BTU/ft , 40 MJ/m ). Hired-Hand, Inc. makes no guarantees regarding the proper operation of this appliance when these conditions are not met. Part No. 4801-1015 Rev 7-2012 Super-Saver XL Heater – 120 Volt, 60Hz, ETL...
Installation 5.1 Hanging The Heater Chain Suspension Cable Suspension Mount the heater with chain hooks and chains so that the back of the heater is at least 12 inches (305 If frequent height adjustment is required, use mm) from the ceiling and wall. The heater must be cables and pulleys.
User Instructions Before turning on gas, check main supply valve to be sure it is open (Fig. 3). Be sure to check all connections for leaks with a Gas Leak Testing solution, (soap and water work well). Check to see if gas valve knob is in the ON position.
Outside Mount (Optional) Hired-Hand heaters are available with Outside Mount (OSM) kits. These heaters are designed to be mounted to the outside wall of a building. This saves valuable space inside the building and ensures fresh air intake for the heater.
Page 11
13. If not already bent, bend the sides of two door covers 90° by hand in the direction of the existing top and bottom bends. See Existing Bend Direction Detail E. 14. Insert tabs of door cover in slots on heater door and slide down. This will lock the cover in place on the door.
10. Servicing Instructions: HSI Model 10.1 United Technologies Hot Surface Ignition System IMPORTANT! Inspect and check operation of this appliance monthly. Follow the instructions below. If a problem is detected, contact a qualified technician to make any necessary repairs. In an effort to minimize the time required to trouble shoot this system: Turn off the gas supply at the main gas valve.
10.2 1018 Series Hot Surface Ignition Status Indicator Error Conditions The status indicator LED will not be lit with power applied to the board and the control operating properly. However, if the control is not operating properly, the status indicator LED will flash in one of the following error codes.
13. Servicing Instructions: DSI Model 13.1 United Technologies Direct Spark Ignition System IMPORTANT! Inspect and check operation of this appliance monthly. Follow the instructions below. If a problem is detected, contact a qualified technician to make any necessary repairs. In an effort to minimize the time required to trouble shoot this system: 1.
13.2 1016 Direct Spark Ignition Status Indicator Error Conditions The status indicator LED will not be lit with power applied to the board and the control operating properly. However, if the control is not operating properly, the status indicator LED will flash in one of the following error codes.
14. Pipe Sizing Guidelines 14.1 Calculating HVR & ELOP Determine the Equivalent Length Of Pipe (ELOP) Using a system schematic, label each piping required for sufficient gas service. section of the system starting at the meter or ELOP = (length from meter to most remote heater) regulator.
Page 27
Table 1 Minor Loss Equivalents Fitting 2" (5.08 cm) IPS Or Smaller 2” (5.08 cm) IPS To 4” (10.16 cm) IPS Feet per fitting Meters per fitting Feet per fitting Meters per fitting 45° Elbow 90° Elbow Gate Valve Angle Valve Swing Valve Pipe Sizes Determined For Diagram Pipe Section...
15. Parts & Assemblies NOTE: CONTACT DEALER FOR REPLACEMENT PARTS 15.1 120-225k BTU (HSI & DSI) When ordering service parts, please specify the country, model number, date of manufacture, voltage, frequency, gas type, inside or outside mount, and whether the heater is constructed of galvanized or stainless steel. Models SS-225-XXL, SS-200-XL, SS-175-XL, SS-120-XL Part No.
Page 29
Models HH-SS-225-XL, HH-SS-200-XL, HH-SS-175-XL and HH-SS-120-XL 0404-11050 0404-11467 6401-0226 6401-0226 0404-11466 6401-1308 1004-1102 1004-1102 1041-5004 1009-1500 SEE MODEL NO. 1041-1488 1004-1422 1021-1495 1021-1500 3004- 0100 LP/Propane Gas 3004- 0101 Natural Gas 1041-1491 1021-1496 Part No. 4801-1015 Rev 7-2012 Super-Saver XL Heater – 120 Volt, 60Hz, ETL Page 29 of 38...
15.2 40k & 75k BTU (HSI & DSI) When ordering service parts, please specify the country, model number, date of manufacture, voltage, frequency, gas type, inside or outside mount, and whether the heater is constructed of galvanized or stainless steel. Model SS-75-XL and Model SS-40-XL Part No.
Page 32
Model SS-75-XL and Model SS-40-XL Part No. 4801-1015 Rev 7-2012 Super-Saver XL Heater – 120 Volt, 60Hz, ETL Page 32 of 38...
Page 33
Models SS-75-XL and Model SS-40-XL 1004-1130 0408-1883 6401-2881 6401-1726 0408-1231 0408-2314 SS-40-XL Only 1001-2599 1004-1410 0408-1146 1004-1130 3001-1740 3017-1302 120V 60 Hz 0408-5017 1001-1452 Part No. 4801-1015 Rev 7-2012 Super-Saver XL Heater – 120 Volt, 60Hz, ETL Page 33 of 38...
Need help?
Do you have a question about the SUPER-SAVER HH-SS-250-XL and is the answer not in the manual?
Questions and answers