1. Manuals
  2. Brands
  3. Steibel Eltron Manuals
  4. Water Heater
  5. DEM 6 220
  6. Instructions for operating and installation

Steibel Eltron DEM 6 220 Instructions For Operating And Installation

Electronically controlled mini instantaneous water heater
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
HTV`.C& C .CZ`<<`.HC
<`VHC.<<t HC`VH<< B.C. .CZ`C`CHeZ q`V +`V
á B

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the DEM 6 220 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Steibel Eltron DEM 6 220

Summary of Contents for Steibel Eltron DEM 6 220

  • Page 1 HTV`.C& C .CZ`<<`.HC <`VHC.<<t HC`VH<< B.C. .CZ`C`CHeZ q`V +`V á B...

  • Page 2: Table Of Contents

    HC`C`Z ’ HTV`.HC &CV< .C%HVB`.HC HTV`.HC OPERATION General information _________________________________________2 Safety instructions _______________________________________________ 2 Other symbols in this documentation _______________________ 3 General information Units of measurement __________________________________________ 3 Safety __________________________________________________________3 The chapter “Operation” is intended for appliance users and quali- Intended use ______________________________________________________ 3 fied contractors.

  • Page 3: Other Symbols In This Documentation

    HTV`.HC Z%`t Other symbols in this documentation CE designation The CE designation shows that the appliance meets all essential Note requirements according to the: Notes are bordered by horizontal lines above and below - Low Voltage Directive the text. General information is identified by the symbol - Electromagnetic Compatibility Directive.

  • Page 4: Cleaning, Care And Maintenance

    If you cannot remedy the fault, notify your qualified contractor. To facilitate and speed up your enquiry, please provide the serial number from the type plate (000000-0000-000000). DEM 6 220 Nr.: 000000-0000-000000 Ô ’ B qqq Z`. <é<`VHC HB...

  • Page 5: Safety

    .CZ`<<`.HC Z%`t .CZ`<<`.HC Preparations f Flush the water line thoroughly. Water installation Safety A safety valve is not required. Only qualified contractors should carry out installation, commis- Taps/valves sioning, maintenance and repair of the appliance. f Use suitable taps (see chapter “Accessories”). General safety instructions Note We guarantee trouble-free operation and operational reliability...

  • Page 6: Connecting The Power Supply

    .CZ`<<`.HC .CZ`<<`.HC Appliance installation Tap installation f Fit the tap according to the illustration. For this, observe the Note tap operating and installation instructions. f Mount the appliance on the wall. The wall must pro- vide sufficient load-bearing capacity. Damage to the appliance and environment f When making any connections, counterhold them on the appliance using a size 14 spanner.

  • Page 7: Commissioning

    .CZ`<<`.HC HBB.ZZ.HC.C& DANGER Electrocution DANGER Electrocution In its delivered condition, is the appliance are equipped with The adjusting screw for setting the flow rate and the po- a power cable for a permanent power supply. tentiometer for setting the temperature are ‘live’ if the You can connect a cable with a maximum cross-section of appliance has not been isolated from the power supply.

  • Page 8: Taking The Appliance Out Of Use

    .CZ`<<`.HC `:.C& `+ TT<.C He` H% eZ Limiting the flow rate LED indicator Factory setting: Maximum flow rate 1 Illuminates red in case of fault 2 Illuminates yellow in heating mode f Using the adjusting screw, set the required maximum flow 3 Flashes green if the electronics are supplied with power rate: Lowest flow rate = turn the screw clockwise.

  • Page 9: Specification

    .CZ`<<`.HC ZT.%.`.HC Clean sieve 15.2 Wiring diagram You can clean the fitted sieve after removing the cold water sup- 1/N/PE ~ 220 V ply pipe. Checking the earth conductor f Should it become necessary to check the earth conductor, do this at the earth conductor contacts and at the appliance connector.

  • Page 10: Increasing The Temperature

    .CZ`<<`.HC ZT.%.`.HC 15.3 Increasing the temperature X Flow rate in l/min Y Temperature increase in K Example: Flow rate 3.4 l/min Temperature increase 25 K Cold water inlet temperature 15 °C Maximum possible outlet temperature 40 °C Hinweis An outlet temperature of 50 °C can be achieved by select- ing the maximum temperature and with the > 12 °C cold water inlet temperature.

  • Page 11: Data Table

    .CZ`<<`.HC ’ qVVC`t ’ Cp.VHCBC` C Vt<.C& ZT.%.`.HC 15.5 Data table 231519 Electrical data Connected load ~ 220 V Rated voltage Rated current 27.8 Fuse Phases 1/N/PE Frequency Max. mains impedance Zmax to DIN EN 61000-3-11 0.37 Specific resistance (≤ 25 °C) Ohm cm 1000 Specific resistance (>...
  • Page 12 Deutschland Verkauf Tel. 0180 3 700705* | Fax 0180 3 702015* | info-center@stiebel-eltron.de STIEBEL ELTRON GmbH & Co. KG Kundendienst Tel. 0180 3 702020* | Fax 0180 3 702025* | kundendienst@stiebel-eltron.de Dr.-Stiebel-Straße | 37603 Holzminden Tel. 05531 702-90015 Tel. 05531 702-0 | Fax 05531 702-480 Ersatzteilverkauf Tel.

Table of Contents