Advertisement
Safety Instructions
EN
Important Safety Instructions
Read all of these instructions before using the printer. Also be sure to follow all warnings and
instructions marked on the printer.
Notes on Installing
Do not obstruct the vents on the product.
If the vents are obstructed, the internal temperature could rise and cause a fire. Do not cover the
printer with a cloth or install it in a location with poor ventilation. Make sure you secure sufficient
space for the installation as described in the manual.
U "Choosing a Place for the Printer" on page 11
Do not install or store the printer in an unstable location or a location subject to vibrations
from other equipment.
The printer could fall or tip over and cause an injury.
Do not install the printer in locations subject to oily smoke and dust, or in locations subject to
humidity or where it could easily get wet.
An electric shock or fire could occur.
Do not tilt the product more than 10 degrees forward, back, left, or right while moving it.
Failure to observe this precaution could result in the printer falling over, causing accidents.
Because the product is heavy, it should not be carried by one person.
Two people are needed to unpack or carry the printer. See the following for details on the
product's weight.
U "Choosing a Place for the Printer" on page 11
When lifting the product, make sure you lift at the locations indicated in the manual.
If you lift holding other parts, the printer may fall, catching your fingers and causing an injury. See
the following for details on lifting the product.
U "Carrying the Printer" on page 12
Make sure you use the correct posture when lifting the product.
Lifting using the wrong posture could cause an injury.
When placing the product on a stand with casters (wheels), make sure you secure the casters
before you perform the work so that they do not move.
If the stand moves while you are performing the work, it could cause an injury.
!
Warning
!
Caution
Notes on Handling
Do not use the printer in locations with volatile substances such as alcohol or thinner, or near
naked flames.
An electric shock or fire could occur.
Do not use the printer if it is giving off smoke or if you notice any abnormal odors or noises.
An electric shock or fire could occur. If any abnormalities occur, turn off the power and unplug the
power cable from the outlet immediately, and then contact your dealer or Epson Support.
Never try to repair the printer yourself as this is extremely dangerous.
Do not use the printer in an environment where flammable gas or explosive gas may exist. Do
not use sprays that contain flammable gas inside or near the product.
A fire could occur.
Only route the cables as indicated in the manual.
A fire could occur. This could also cause damage to connected devices.
Do not insert or drop any metallic or flammable items into the openings on the printer.
An electric shock or fire could occur.
Do not touch any areas inside the printer except for those indicated in the manual.
An electric shock or burn could occur.
Do not disassemble anything except when indicated to do so in the manual.
If the LCD for the control panel is damaged, be careful of any leaking liquid crystal.
Provide first aid under any of the following conditions.
❏ If liquid adheres to your skin, immediately wipe it off and then wash the area using large volumes
of soapy water.
❏ If any liquid gets in your eyes, flush them with clean water for at least 15 minutes, and consult a
physician immediately.
❏ If liquid is swallowed, rinse your mouth out with water, swallow large quantities of water and
vomit it back up, and consult a physician immediately.
If any foreign objects or liquid such as water enters the printer, stop using it immediately.
An electric shock or fire could occur. Turn off the power and unplug the power cable from the
outlet immediately, and then contact your dealer or Epson Support.
Do not sit on the product or place any heavy objects on the product.
The printer could tip over or break and cause an injury.
Do not put your fingers close to the ejection rollers when the power is turned on or during
printing.
There is a risk that your fingers could get caught in the ejection rollers, resulting in injury. Wait until
the paper is fully ejected before picking it up.
!
Warning
!
Caution
5
Advertisement
