Xerox DocuTech 180 Install Manual page 2

Installation Preparation Document
Paper Handling
•
16 to 110 lb. (60 to 200 gsm) cut sheet paper weights
•
8 by 10 in. to 14.33 x 17 in. (203 by 254 mm to 364 by 432 mm)
including A4, A3, and B4 paper sizes (destination dependent)
•
7 by 10 in. (178 by 254 mm) optional enablement kit
•
Transparencies, label stock, tab stock, carbonless paper, pre-
perforated stock
•
Paper stock weights less than 16 lb. are not recommended.
•
Textured stocks are not recommended.
•
Some 65 lb. stocks may not fully fuse.
Input
Tray
Main tray (tray 1)
Auxiliary tray (tray 2)
High capacity trays (trays 3 and
5)
Fuser bypass tray (tray 4)
Output
Tray
Stacker
Stitcher
Binder
Top tray
Environmental Requirements
Temperature
Humidity
Non-condensation
Heat Emission - printer
Altitude (above sea level)
701P46151
October 2006
Xerox DocuTech 180 HighLight Color
Capacity
1,100 sheets 20 lb (75
gsm)
600 sheets 20 lb (75 gsm)
2,600 sheets each 20 lb
(75 gsm)
550 sheets each 20 lb (75
gsm)
Capacity
3000 sheets 20 lb (75 gsm)
2 - 70 sheets 20 lb (75
gsm)
~35,000 stitches per spool
15-125 sheets 20 lb (75
gsm)
~425 11 in binds per spool
500 sheets 20 lb (75 gsm)
o
50 to 85 F
o o
(10 to 29 C)
30 to 65% RH
4454 BTU/Hr
(Standby)
32,770 BTU/Hr
(Operating)
Up to 6,000 ft
(1830 m)
(for physical installation of the product only)
Operating Supplies
Dry Ink - Black
Dry Ink – Blue
Dry Ink – Red
Dry Ink – Green
Dry Ink – Royal Blue
Dry Ink – Cardinal Red
Dry Ink – Cyan
Dry Ink – Magenta
Dry Ink – Yellow*
Developer (Black, Red,
Blue, Green, Royal Blue,
Cardinal Red, Cyan,
Magenta, Yellow)
Fuser Blend
Fuser Shield
Dry ink waste container
HLC developer waste bottle
Binder tape – Black
Binder tape – White
Binder tape – Gray
Binder tape – Blue
Stitcher Wire
* Will be available in the near future.
NOTE: The formula for the DocuTech HLC fuser lubricant was
changed in 2006 to provide better image quality and to prevent image
transfer. The new fuser formula is called Fuser Shield. The Fuser
Blend and the Fuser Shield CANNOT be intermixed in a DocuTech
HLC. To change from one fuser lubricant to another requires a
service call and cleaning or replacing components. The two fuser
formulas are identified with different color bottles and caps.
If a machine is running with in-line finishing equipment, the new Fuser
Shield may contribute to poor binding at the binder glue seam.
Customers experiencing this problem can have their equipment
returned to using Fuser Blend by placing a service call to clean
and/or replace components. Do NOT place Fuser Blend in a
machine that has been using Fuser Shield.
•
Monthly duty cycle is up to 6 million (DT 180 HLC).
•
The Xerox Supplies Marketing Center, 1-800-822-2200, is
available for ordering Xerox supplies, including paper and other
throughput material.
•
The supply of developer for each of the color toners is ordered
and maintained at the customer site by the Xerox Service
Representative and is not orderable by the customer.
•
The Dry ink waste container supply is maintained at the
customer site by the Xerox Service Representative and is not
orderable by the customer.
Reorder No.
6R206 (US/CA)
6R1191 (US/CA)
6R90343 (XE)
6R1192 (US/CA)
6R90344 (EU)
6R1193 (US/CA)
6R90345 (EU)
6R1255 (US/CA)
6R90356 (XE)
6R1277(US/CA)
6R90358(XE)
6R1284(US/CA)
6R90359(XE)
6R1296 (US/CA)
6R90360 (XE)
6R1299 (US/CA)
6R90361 (XE)
NA
8R12938 (1 bottle)
8R12939 (6 bottles)
8R4077 (1 bottle)
8R7618 (6 bottles)
NA
604K24870 (4 bottles)
8R7186
8R7187
8R7188
8R7189
8R1174