Page 5
手提式无线扩音器 功能示意 扩音器 ⑩ ① ② ⑥ ⑦ ⑧ ⑨ ⑤ ③ ④ ① 电源开关&麦克风音量旋钮:关机状态下,向“开”方向旋转旋钮,听到“哒” 一声,表示扩音器已开机,此时电源指示灯蓝灯常亮,并伴随语音提示(麦克 风模式);继续向“开”方向旋转声音逐渐增大,反之向“关”方向旋转则声 音逐渐减小,直至听到“哒”一声关机。 ② 伴奏音量旋钮:在USB、无线播放、收音、音频输入模式播放状态下,顺时针 旋转增大伴奏音量,反之减小伴奏音量。 ③ 混响调节旋钮:顺时针旋转增大麦克风混响效果,反之减小麦克风混响效果。 ④ 高低音调节旋钮:向左旋转逐渐增加伴奏的低音比例,向右旋转逐渐增加伴奏 的高音比例。 ⑤ 功能切换键:开机状态下,短按该按键可切换工作模式,并伴随相应的语音提示。...
Page 8
手提式无线扩音器 手持麦克风 ① ② ③ ④ ① 液晶显示屏:显示频率、麦克风信号、电池电量等信息。 ② 电源按键:长按3秒开启或关闭麦克风;循环点按此键调节麦克风音量,分为 (U08-U11)共4级音量,调节麦克风音量时扩音器会同时发出“滴”的一声提 示音。 ③ “HI/LO”按键:用于对频操作,详见本说明书“对频方法”部分。 ④ 电池仓:装入2节1.5V AA电池。...
Page 9
手提式无线扩音器 麦克风显示屏 ① 电池电量:电池电量有三格,以格数表示电池电量,电量不足时,电池符号闪 烁,请及时更换电池。 ② 信号符号:“ ”表示麦克风信号。 ③ 频率信息:显示当前麦克风的工作频率,(635.5MHz-654.5MHz)共20个频率; 对频操作时,频率闪烁。 ④ 音量信息:调节麦克风音量时,屏幕显示“U 00”表示当前麦克风音量等级, 3秒后恢复显示频率信息。 麦克风电池安装 逆时针扭开麦克风尾盖,将2节5号干电池按电池仓标明的正负极性安装,注意电 池极性不要装反;然后顺时针旋紧麦克风的尾盖。如下图:...
Page 10
手提式无线扩音器 头戴麦克风 ⑨ ③ ⑧ ④ ⑦ ⑤ ① ② ⑥ ① 电源开关:向ON方向推动,蓝灯⑥亮,表示麦克风已经进入开机状态; 向OFF方向推动,蓝灯⑥熄灭,表示耳麦已经进入关机状态。 ② 充电插口:将Type-C充电线插入此孔,另一端连接通用的USB输出充电 器,即可进行充电,充电指示灯红灯亮。 ③ “M”频道切换按键:用于调频操作,详见本说明书的“对频方法”部分。 ④ “+”按键:点按增加麦克风音量;在对频状态下,点按切换上一个频道, 长按快速跳转频道。 ⑤ “ ”按键:点按减小麦克风音量;在对频状态下,点按切换下一个频道, - 长按快速跳转频道。 ⑥ 指示灯:关机未充电时,指示灯熄灭;开机时常亮蓝灯;电量充足时,指示 灯常亮蓝灯;电量不足时,指示灯蓝灯闪烁;充电过程中红灯常亮,充满后 红灯熄灭。 ⑦ 显示屏:显示工作频道、麦克风音量、功率模式。 ⑧ 工作频道/麦克风音量:默认显示当前工作频道,有“01-20”共20个工作频 道;当点按音量“+”、“-”键时,则显示音量大小,有“U1-U8”共8级音 量,3秒后恢复正常数值;10秒后无任何操作,显示屏将自动熄灭。...
Page 15
Portable Wireless Amplifier Preface Dear Customer, Thank you for purchasing Takstar E17 Portable Wireless Amplifier – New Edition To better understand and use the product, please read this manual carefully. If you have any questions or suggestions, please contact our local dealer.
Page 17
• Battery Capacity: 3.7V 400mAh • Charging Specification: DC 5V 200mA • Charging Time: Approx. 2 hours • Battery Life: Approx. 5 hours • Weight: Approx. 39g Note: The above data are measured by Takstar laboratory which has the final interpretation right!
Portable Wireless Amplifier Function Descriptions Voice Amplifier ⑩ ① ② ⑥ ⑦ ⑧ ⑨ ⑤ ③ ④ ① Power Switch & Mic Volume Knob: Rotate towards ON direction until you hear a click to power up the device. The power indicator will light up solid blue, accompanied by a voice prompt (microphone mode).
Page 19
Portable Wireless Amplifier ④ Bass & Treble Knob: Rotate to the left to increase the bass proportion of the accompaniment. Rotate to the right to increase the treble proportion of the accompaniment. ⑤ Function Switch Button: When powered on, short press to switch between different working modes, accompanied by corresponding voice prompts.
Page 20
Portable Wireless Amplifier ⑱ ⑲ ⑰ ⑯ ⑮ 充电 电源 功能 循坏 ⑬ ⑫ ⑪ ⑭ ⑪ Mic Input Interface: Connect a wired mic to enter wired voice amplification mode. Please avoid pointing the mic's pickup side towards the speaker of the amplifier to prevent feedback.
Page 21
Portable Wireless Amplifier ⑰ UHF Indicator: Displays the connection status between the transmitter and the amplifier. Solid blue when connected and turns off when disconnected. ⑱ Function Indicator: Displays the mode status. Rapid blue flashes in wireless playback mode when not connected, and turns slow blue flashes once connected.
Page 22
Portable Wireless Amplifier ① LCD Display Screen: Shows frequency, mic signal, battery level, and other information. ② Power Button: Long press for 3 seconds to power on or off the mic. Press to adjust the mic volume cyclically. There are 4 levels of volume (U08-U11), and the amplifier will beep when adjusting the mic volume.
Page 23
Portable Wireless Amplifier Wireless Mic Battery Installation To install the mic battery, unscrew the mic bottom cap counterclockwise. Install two AA batteries according to the polarity indicated in the battery compartment. Then, rotate the mic bottom cap clockwise to tighten it back. See figure below.
Page 24
Portable Wireless Amplifier ① Power Switch: Slide to the ON or OFF position to turn on or off the device respectively. ② Charging Port: Insert the Type-C charging cable and connect to a standard USB output charger for charging. ③ M Channel Switch Button: Used for frequency adjustment, refer to the Frequency Pairing section in this manual for details.
Page 25
Portable Wireless Amplifier Operation Instructions I. Pairing Method The products are paired by factory default and will automatically connect to each other once powered on. No extra pairing is required. If there is signal interference, follow the below steps to re-pair or change frequency. Handheld Microphone 1.
Page 26
Portable Wireless Amplifier Headset Microphone 1. Frequency Pairing ① Ensure that both the headset mic and the amplifier are powered off. Then, turn on the power of the headset mic. Press and hold the [M] button on the mic for 3 seconds until the display screen starts cycling.
Page 27
2. Enter SETTINGS menu on your phone, find and enable wireless function, wait until "TAKSTAR E17" is discovered and tap on it to connect. When connected successfully, the function indicator will flash slowly in blue and there will be a voice prompt about wireless connected.
Portable Wireless Amplifier Safety Instructions To avoid electric shock, overheat, fire, radiation, explosion, mechanical risk and injury or property loss due to improper use, please read and observe the following items before use: 1. Please check if the power of the connected equipment matches with that of this product before operation.
This manual contains up-to-date technical specifications as of printing. However, specifications contained herein may not conform to your particular product since Takstar is constantly improving its products. Also, specifications, devices or accessories available may vary from region to region. If you have any questions, please contact our local sales outlet. For the latest version/more information, please visit our website: https://www.takstar.com/...
Need help?
Do you have a question about the E17 and is the answer not in the manual?
Questions and answers