Page 4
E126W 便携式无线扩音器 功能示意: ⑥ ④ ⑤ ① ⑦ ② ③ 扩音器: ① 电源开关:向“ON”方向拨动旋钮,听到“滴”一声,此时电源指示灯亮蓝灯, 表示扩音器已通电并进入人声扩音状态,继续向“ON”方向拨动旋钮声音增大, 反之向“OFF”方向拨动则声音减小直至听到“滴”的一声关机; ② 电源指示灯:充电时,指示灯长亮红灯;红灯熄灭,蓝灯长亮表示电已充满; 扩音过程中红蓝灯闪烁表示低电压,当此红蓝灯闪烁时,请及时为扩音器充电(充 电时建议将扩音器关机); ③ MIC IN输入插孔:ø3.5mm的麦克风插头插入此孔,进入有线麦人声扩音工作状 态;(插入有线麦后无线麦将停止工作); ④“M”模式切换按键:开机状态下,循环点按“M”键,可切换蓝牙模式和麦克 风模式,并有相应的语音提示; ⑤ 充电接口:通过Type-C充电线为扩音器充电; ⑥ 挂扣:用于安装肩带,可将扩音器斜挂于肩上使用; ⑦ 背扣:用于将扩音器扣于腰带或裤腰上使用。...
PORTABLE WIRELESS AMPLIFIER Preface Dear Customer, Thank you for purchasing Takstar E126W Portable Wireless Amplifier. In order to better understand and use the product, please read this manual carefully. If you have any questions or suggestions, please contact our local dealer.
Sensitivity: -51~-54dB UHF Frequency: 630MHz-698MHz (segmented) UHF Effective Range: approx. 40m, open area Battery Type: Lithium-ion battery Battery Capacity: 3.7V/400mAh Charging Method: DC 5V 150mA Note: The above data is measured by Takstar laboratory, and Takstar has the final interpretation right!
E126W PORTABLE WIRELESS AMPLIFIER Function Descriptions ⑥ ④ ⑤ ① ⑦ ② ③ Voice Amplifier ① Power Switch: slide the knob towards “ON” until you hear a “click” to power up the device into voice amplification mode, indicated by the lit blue power indicator.
Page 12
E126W PORTABLE WIRELESS AMPLIFIER ④ “M” Button: when powered on, press to switch between Bluetooth Mode and Microphone Mode, indicated by respective voice prompt. ⑤ Charging Port: accepts Type-C charging cable for charging the amplifier. ⑥ Strap Clip: used to install a strap for wearing the amplifier across shoulder.
Page 13
E126W PORTABLE WIRELESS AMPLIFIER ③ Volume Control: press “+” once to increase microphone volume, or “−” once to decrease. ④ Sync/Power Indicator: when powered up, this indicator is off when the headset microphone is out of battery; flashes blue when microphone is low on battery.
Page 14
LED. ② Enter Settings menu on your phone, find and enable Bluetooth, wait until “TAKSTAR E126W” is discovered and tap on it to connect. When paired successfully, the LED will resume lit permanently, and there will be a voice prompt “Bluetooth Connected”. Devices such as cell phones, laptops, tablets and iPads can play music after successful Bluetooth connection with the product.
E126W PORTABLE WIRELESS AMPLIFIER Safety Instructions To avoid electric shock, overheat, fire, radiation, explosion, mechanical risk and injury or property loss due to improper use, please read and observe the following items before use: 1. Please check if the power of the connected equipment matches with that of this product before operation.
Page 16
E126W PORTABLE WIRELESS AMPLIFIER 7. Please abide by safety rules during operation. Do not use the product in places prohibited by laws or regulations to avoid accident. 8. Do not disassemble or repair the product by yourself to avoid injury. If you...