Advertisement
BUS address
06H：D7-D0 Contrast Adjustment
07H：D7-D0 Brightness Adjustment
08H：D7-D4 Cr Gain Adjustment
08H：D3-D0 Cb Gain Adjustment
09H：D7-D4 Cr Output OFFSET adjust. Fine tune for offset of the Cr at output stage.
09H：D3-D0 Cb Output OFFSET adjust. Fine tune for offset of the Cr at output stage.
0AH：D7-D1 HUE adjustment
0AH：D0
Filter for feed-back
0BH：D7-D2 HUE Bias adjustment
0BH：D1
C Trap for dirital clamp. It is C-Trap for Digital-clamp of Y. [1]:ON [0]:OFF
0BH：D0
V-mask of digital clamp Setup of the digital clamping at V-Blk period.
0CH：D7-D4 Offset adjustment for
clamp Y-input
0CH：D3
C-trap of D-COMB
0CH：D2-D0 Take off Filter select Setup Take-off-Filter.
0EH：D7-D5 Phase adjustment of
Digital-clamp for Y.
OEH：D4-D2 Adjustment of clamp-
width for Y-digital
-clamp
0EH：D1-D0 Time constant of Y-
Digital-clamp
0FH：D7-D4 Offset adjustment for
Cr-Input
OFH：D3-D0 Offset adjustment for
Cb-Input
10H：D7-D4 Adjustment of input
clamp phase for Cb/Cr
Feb./2005
Function
It set the Contrast. (Reference value: [01000000])
Variability is ×0.5〜×2.4.
（When use big value and inputs big amplitude signal,
It takes place over range of internal circuit.)
It set the Brightness.
Variability is -128LSB 〜 +128LSB.
It set Gain of Cr. (Refrence value:[0000])
Variability is ×0.5〜×1.4.
（When use big value and inputs big amplitude signal,
It takes place over range of internal circuit.)
It set Gain of Cb. (Refrence value:[0000])
Variability is ×0.5〜×1.4.
（When use big value and inputs big amplitude signal,
It takes place over range of internal circuit.)
HUE adjustment at the NTSC input mode.
Variable is -45°-+43.6 °.
Setup BPF for feed-back-clamp. [1]:ON [0]:OFF
Normaly It must be set [1].
Fine tune HUE-Bias at the NTSC input mode.
Variable is 0°〜+45°.
Use [1] at the digital-clamp-mode.
[1]: Clamp OFF [0]: Clamp ON. It usually uses on [1].
Offset adjustment for Y signal at Analog-input.
Use with 0[mV] when you use with digita-clamp.
Setup C-trap for Y at Digital-COMB-block.
[1]: ON [0]: OFF. This setup can reduce Cross-color and beat.
Take-off-Filter is put in front of Decoder. 000：OFF、001：
BPF、010〜111：TOF（TOF1〜TOF6）
When BPF is set up, it can't get the effect of TOF.
Digital-clamp is put by input-Y-signal
Adjustment of the phase of Digital-clamp-pulse for Y.
Reference value:[011].The variable is about 0.3[μs] step.
Adjustment of the width of Digital-clamp-pulse for Y.
Reference value: [011].Variable is about 0.3[μs] step.
It can select ON/OFF of Digital-clamp-Y. And adjustment of
time constant of Digital-clamp-Y.
Adjust the offset of the Cr at input by YCbCr signal.
Use with 0[mv] at the time of Digital-clamp.
Variable is -31[mV] 〜 +27[mV].
Adjust the offset of the Cb at input by YCbCr signal.
Use [0000] at the Digital-clamp mode.
Variable is -31[mV] 〜 +27[mV].
Adjust the clamp-phase of Cb/Cr at YCbCr signals.
It usually uses on BUS:[0000].
Contents
TC90101FG
22
Advertisement
