Download
Share
Print this page
  1. Manuals
  2. Brands
  3. Xantech Manuals
  4. Switch
  5. 686-10
  6. Installation instructions

Xantech 686-10 Installation Instructions

Remote speaker switcher
Hide thumbs
1
2
3
4
5

Advertisement

Quick Links

Download this manual
The 686-10 is an infrared remote controlled Speaker Switcher. It allows the user to turn six stereo pairs of
speakers ON and OFF by way of IR commands from a Xantech RC68+ (or RC68) Programmer. The RC68+
commands are "taught" to learning devices and passed to the 686-10 signal input terminals via Xantech IR
receivers and keypads. Individual speaker pairs may be turned on or off in any particular room or all
speakers turned on and off from any room for a "party mode".
FEATURES AND SPECIFICATIONS
• 200 watts per channel capacity.
• Switchable 4-Ohm series resistor for amplifier protection.
• Seven 4-terminal plug-in connectors. One for the amplifier input and 6 for the stereo, relay-switched
speaker outputs.
• Isolated Left and Right Grounds allow use of bridging type power amplifiers.
• 4-terminal IR input for Xantech IR Receivers, SmartPads, connecting blocks and other devices.
• IR Confirm LED lights only with RC68+ On/Off, Toggle & Group IR commands.
• RC68+ IR commands permit Toggle, Pair and Group mode operations as well as different IR codes for
use of multiple 686-10's. The 686-10's Code Group number is 98.
• Universal mounting fits 19-inch racks or any 3-1/2" X 19" surface. Projects about 2-3/4 inches behind
panel with cables connected.
• Requires RC68+ Programmer (or an RC68) and 782-00 Power Supply.
• Power: 12 VDC @ 300mA.
• Dimensions: 19" W x 3-1/2" H x 2-1/4" D.
RC68 PROGRAMMER / REMOTE CONTROL
The RC68+ Programmer (available separately) contains all commands necessary to operate the 686-10
(see Fig. 2).
• You will need it to program universal learning devices such as the Xantech URC-1 learning remote, the
Xantech Smart Pads, the 590 Controller, the 710 Fone Link, etc., with commands that operate the 686-
10.
• NOTE: The RC68+ codes operate several other Xantech models as well, such as the RS41AV, CC12,
ZPR68, etc. Therefore, only the button descriptions that apply to the operation of the 686-10 are
listed. All others should be ignored.

INSTALLATION INSTRUCTIONS

686-10
REMOTE SPEAKER SWITCHER
PROTECTION
RESISTOR
OUT
1
2
O N
O N
1 2 3 4 5 6
1 2 3 4 5
I N
L+
L-
IR CONFIRM
R-
R+
12 VDC
Fig. 1 The Model 686-10 Remote Speaker Switcher
SPEAKER
3
4
5
6
LEFT
LEFT GND
RIGHT GND
RIGHT
686-10
REMOTE SPEAKER SWITCHER
®
1

Advertisement

loading

Related Manuals for Xantech 686-10

Summary of Contents for Xantech 686-10

  • Page 1: Installation Instructions

    REMOTE SPEAKER SWITCHER The 686-10 is an infrared remote controlled Speaker Switcher. It allows the user to turn six stereo pairs of speakers ON and OFF by way of IR commands from a Xantech RC68+ (or RC68) Programmer. The RC68+ commands are "taught"...
  • Page 2 MMT code is being sent. The relay is normally OFF. GP-ON (Group ON) - This button (labeled F8 on the button face) causes the 686-10 to turn all speaker relays ON at the same time. GP-ON overrides all individual settings.

  • Page 3: Installation

    Power Interruption Status The 686-10 should normally be plugged into an unswitched AC outlet. However, if the power to the 686- 10 is interrupted by a power failure or other reason, the internal memory will retain the last selected switched status for each of the speaker relays.
  • Page 4 1. The Model 686-10 is intended to be mounted on a vertical surface so that the ventilation slots are at the top and the bottom of the unit. Air should be allowed to circulate into the bottom slots and out of the top slots, particularly when the PROTECTION RESISTOR is switched IN.
  • Page 5 INPUT AMPLIFIER 2-1-01 Rev.C 686-10 INPUT INPUT AMPLIFIER AMPLIFIER ® V G G S V G G S V G G S V G G S V G G S V G G S V G G S V G G S...