Advertisement
Quick Links
The Model 680-10 is an IR Remote Controlled AC Switcher with six AC outlet receptacles. It accepts RC68+
(or RC68) IR Programmer commands coming from any Xantech IR receiver, keypad, or controller direct-
wired to its IR Input port. Switching modes of ON, OFF, Toggle, Momentary and Group are possible. Each
outlet is switched ON or OFF by a high current electromechanical relay for higher reliability than solid state
switching methods.
Sequential ON commands for each outlet are possible when used in conjunction with learning devices, such
as Xantech URC-1 remotes, Smart Pads, or 590 controllers.
Since the 680-10 has 30 installer-adjustable IR code groups, it allows multiple 680-10's to be individually
controlled when used in the same system.
➧
RESET
120 VAC
15A MAX
Fig. 1 Model 680-10 IR Remote Controlled AC Switcher
FEATURES AND SPECIFICATIONS
• Six AC Outlets rated at 120 VAC, 5 Amps each.
.
• 15 Amps total current rating.
• Includes 15-Amp circuit breaker.
• 14-Gauge heavy duty 3-conductor power cord, 5-1/2 feet in length, with a grounded 3-prong plug.
• IR input jack (3.5mm mini phone jack)
• An LED indicator lights to confirm the presence and acceptance of 680-10 IR commands.
• Requires RC68+(or RC68) hand-held Programmer codes set to a matching IR code group.
• The 680-10 is factory preset to code group 88.
• Dimensions: 15-1/2" W x 4-1/2" D x 2-3/8" H..
RC68+ PROGRAMMER / REMOTE CONTROL
The RC68+ (or RC68) Programmer (available separately) contains all the commands necessary to operate
the 680-10 (see Fig. 2).
• You will need it to program universal learning devices such as the Xantech URC-1 learning remote, the
Xantech Smart Pads, the 590 Programmable Controller, the 710 Fone Link, etc., with commands that
operate the 680-10.
• NOTE: The RC68+ codes operate several other Xantech models as well, such as the RS41AV, CC12,
ZPR68, etc. Therefore, only the button descriptions that apply to the operation of the 680-10 are
listed in the Button Descriptions section. All others should be ignored.
INSTALLATION INSTRUCTIONS
680-10
REMOTE AC SWITCHER
OUTLET 1
OUTLET 2
5A MAX
5A MAX
TOTAL LOAD LIMITED TO 15A
OUTLET 4
OUTLET 5
5A MAX
5A MAX
OUTLET 3
5A MAX
680-10
REMOTE AC SWITCHER
TEMPORARY POWER TAP
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK
USE INDOORS IN A DRY LOCATION.
OUTLET 6
5A MAX
IR
CONFIRM
INPUT
1
Advertisement
Related Manuals for Xantech 680-10
Summary of Contents for Xantech 680-10
- Page 1 INSTALLATION INSTRUCTIONS The Model 680-10 is an IR Remote Controlled AC Switcher with six AC outlet receptacles. It accepts RC68+ (or RC68) IR Programmer commands coming from any Xantech IR receiver, keypad, or controller direct- wired to its IR Input port. Switching modes of ON, OFF, Toggle, Momentary and Group are possible. Each outlet is switched ON or OFF by a high current electromechanical relay for higher reliability than solid state switching methods.
- Page 2 RC68+ to the same number! It may be necessary to change the 680-10 to a different code group if it is used in a common IR bus controlled system with other Xantech 680-10's, to avoid mutual interaction. Refer to the RC68+ instructions for code group setting details and procedures! Outlet Command Modes.
- Page 3 NOTE: The 680-10 should normally be plugged into an unswitched AC outlet. However, if the power to the 680-10 is turned off by a power failure, or other means, the internal memory will retain the last selected switched condition for each of the outlets.
- Page 4 The 680-10 has four attached rubber feet for stand-alone mounting. Underwriters Laboratories defines the 680-10 to be a moveable device and therefore it is not to be fastened down permanently to any surface. It may however, be placed in any orientation to accommodate the installation.