Related Manuals for Absolute Innovations Kiser Edge
Summary of Contents for Absolute Innovations Kiser Edge
- Page 1 Kiser Edge Setup Guide 8’ Kiser Edge shown **PLEASE READ AND UNDERSTAND BEFORE OPERATION** Version 2.0.7 ABI( ) - 1320 Third Street, Osceola IN 46561 - 855-211-0598 Absolute Innovations, Inc. www.abiattachments.com...
-
Page 2: Additional Contact Information
These instructions are designed to help you get your new Kiser Edge off the delivery pallet and into use. Once you have put your Kiser Edge to work, if you have any questions, please feel free to call and talk with our friendly and knowledgeable Customer Service Department. -
Page 3: Operational Safety Rules
Exercise caution at all times with using the Kiser Edge. Never permit any person to ride or board the Kiser Edge at any time. NEVER ALLOW RIDERS ON ANY ABI MODEL KISER EDGE! ... - Page 4 Please read fully and understand prior to operating the Kiser Edge Information on your Kiser Edge- Revolutionary Design: Designed by the World's leading expert on horse arena footing, Bob Kiser, the Edge offers a radical change in arena footing maintenance. With its revolutionary "Profile Blade Technology" the Edge grooms every square inch of the footing material and safely cleans the base, under the surface, of dangerous compaction layers.
-
Page 5: Optional Features
Rail / Wall Blade: The rail blade attaches to the frame of the Kiser Edge on the right hand side using a hitch pin. The shovel cuts into the built up material along arena walls and rails and pulls it back into the arena, saving the user time and effort when grooming your arena. - Page 6 Profile Blades are running level with the arena base. 1. With the Kiser Edge attached to the 3 point of a Tractor, take the Kiser Edge to an area with a hard flat surface. 2. To level the Kiser Edge for operation, go to section “Setting the Profile Blades for use”.
- Page 7 2. Next, Lower the Kiser Edge down on the flat hard surface until the wheels sit firmly on the ground. Ensure the finish rake does not dig into the surface when the Kiser Edge is lowered to the ground. If the finish rake hangs up on the surface when lowered, raise the Kiser Edge until the finish rake is free, and then lower it slowly while moving forward with the tractor to make sure the finish rake does not hang up.
- Page 8 If the profile blades are not running level to the base of your arena you will need to adjust the Kiser Edge using the top link on your Kiser Edge. If the depth of the Profile Blades must be adjusted refer to the section above and repeat this process from step 1.
- Page 9 Please read fully and understand prior to operating the Kiser Edge Floating Comb/Finish Rake with Tension Chain – **Notice to Owner – Kiser Edge Models after 3/2014 will not have the tension springs with the tension chain. The floating comb on the Kiser Edge is shipped in the center holes with the welded tab on the uprights facing toward the front the Kiser Edge.
- Page 10 Attaching the Optional Wall Blade – 1. Insert the Wall Blade into the opening in the frame on the right hand side of the Kiser Edge. 2. Attach the Optional Wall Blade using the provided hitch pin and lynch pin.
-
Page 11: Maintenance
Checking Hardware- Before each use check to make sure that none of the attaching hardware on the Kiser Edge is loose or damaged, i.e. nuts, bolts, or pins. If any is found to be loose, ensure it is properly secured prior to using the Kiser Edge. If hardware is damaged replace it prior to operation. All hardware on the Kiser Edge is Standard S.A.E Grade 5 hardware. - Page 12 Please read fully and understand prior to operating the Kiser Edge If there are additional questions about the Kiser Edge please feel free to contact our Customer Service Department at 855-211-0598 M-Th 8am-8pm and Friday 8am-5pm EST. For additional resources also check out our support page at www.ABIsupport.com...