Subscribe to Our Youtube Channel
Related Manuals for Davey SpaPOWER SP400P
Summary of Contents for Davey SpaPOWER SP400P
- Page 1 SP400P & SP601 Models: SP400P, Q400PAU-10, Q400PAU-15, SP601AU-15, SP601AU-15T, Q601AU-20, SP601AU-20T Q601AU-15, Q601AU-30, SP601AU-30T User’s Guide...
-
Page 2: Installation & Safety Notes
Means for all pole disconnection must be provided in the fixed wiring in accordance with the wiring rules. 7. If the supply cord is damaged, please refer to Davey water products or Davey authorised service agent for repair or replacement to avoid hazard. -
Page 3: Touch Pads
9. For proper operation the spa pool must be fitted with an effective thermally insulating cover when not in use. 10. The floor or base on which the pool is installed has to be capable of supporting the expected load. 11. -
Page 4: Temperature Control
H20 LED (24hr circulation pump fitted) Theyellow H20lightindicatesifwaterispresentintheheater.IfnowaterisdetectedthentheLED will flash and the unit will not operate except to run the circulation pump to try to get water to the heater. If no water reaches the heater for one minute then an H20 error will occur. If this happens thenpushingthepumpbuttonwillrunthecirculationpumpforanotherminute. -
Page 5: Pump Operation
To select the heating mode first press the Pump and Down buttons simultaneously to display the current heating mode, then press and hold the Up or Down buttons to change modes. 3. PUMP OPERATION There are four possible variations of pump 1 that may have been fitted to your spa, this user guide covers all variations of pump 1 that could have been fitted. - Page 6 3.3 Pump 1 (Two speed, no 24HR circulation pump fitted) Pump 1 is controlled by just one touch pad button pushing the pump button 4 times cycles its operation through 4 modes Automatic, Manual Low Speed, Manual High Speed and Standby. When the spa is running in automatic mode, pressing the pump 1 button will deactivate auto mode and set the pump running in Manual low speed.
-
Page 7: Adjustable Speed Mode (Spvsb Only)
Push 1 - Blower ON (Full Speed) Light Push 2 - Blower ADJUSTABLE (Adjustable Speed) Orange Light Green Push 3 - Blower OSCILLATING (Oscillating Speed) Light Push 4 - Blower OFF (Default State) Light Note: If left on, this accessory will automatically switch off after 20 minutes. If the heater element is on, switching on this accessory may cause the heater to loadshed and switch off.This is to keep the total power load to a safe level. -
Page 8: Indicator Light
5.2 Indicator Light A small red dot in the bottom corner of the digital readout indicates when the light is turned on. If left on the light will automatically switch off after 30 minutes. 6. LIGHT OPERATION 6.1 No 24hr Circulation Pump Fitted The Spa Power controller automatically maintains the filtration/sanitising of the spa pool water. - Page 9 7. SLEEP TIMER (Optional Timeclock) If the optional time clock has been fitted, sleep mode is used to disable automatic temperature maintenance and filtration in order to silence the spa pool during your hours of sleep.The sleep time setting is done using the digital time clock on the front of the control box (See below for setting instructions).
-
Page 10: Self-Diagnostic Error Codes
8. SELF-DIAGNOSTIC ERROR CODES The Spa Power controller has extensive self diagnostic capabilities. In the event of a problem it will indicate an error number according to the nature of the problem. The error numbers and their meanings are listed below. - Page 12 Use of an App is not a substitute for the User’s own vigilance in ensuring the product is working to expectation. Use of a Smart Product App is at the User’s own risk. To the fullest extent permitted by law Davey disclaims any warranties regarding the accuracy, completeness or reliability of App data.
Need help?
Do you have a question about the SpaPOWER SP400P and is the answer not in the manual?
Questions and answers