Advertisement
Table of Contents
Davey Repair or Replacement Guarantee
In the unlikely event in Australia or New Zealand that this Davey product develops any malfunction
within two years of the date of original purchase due to faulty materials or manufacture, Davey will at
our option repair or replace it for you free of charge, subject to the conditions below.
Should you experience any difficulties with your Davey product, we suggest in the first instance that
you contact the Davey Dealer from which you purchased the Davey product. Alternatively you can
phone our Customer Service line on 1300 367 866 in Australia, or 0800 654 333 in New Zealand, or
send a written letter to Davey at the address listed below. On receipt of your claim, Davey will seek to
resolve your difficulties or, if the product is faulty or defective, advise you on how to have your Davey
product repaired, obtain a replacement or a refund.
Your Davey Two Year Guarantee naturally does not cover normal wear or tear, replacement of product
consumables (i.e. mechanical seals, bearings or capacitors), loss or damage resulting from misuse
or negligent handling, improper use for which the product was not designed or advertised, failure to
properly follow the provided installation and operating instructions, failure to carry out maintenance,
corrosive or abrasive water or other liquid, lightning or high voltage spikes, or unauthorized persons
attempting repairs. Where applicable, your Davey product must only be connected to the voltage
shown on the nameplate.
Your Davey Two Year Guarantee does not cover freight or any other costs incurred in making a claim.
Please retain your receipt as proof of purchase; you MUST provide evidence of the date of original
purchase when claiming under the Davey Two Year Guarantee.
Davey shall not be liable for any loss of profits or any consequential, indirect or special loss, damage
or injury of any kind whatsoever arising directly or indirectly from Davey products. This limitation
does not apply to any liability of Davey for failure to comply with a consumer guarantee applicable to
your Davey product under the Australian or New Zealand legislation and does not affect any rights or
remedies that may be available to you under the Australian or New Zealand Consumer Legislation.
In Australia, you are entitled to a replacement or refund for a major failure and for compensation for
any other reasonably foreseeable loss or damage. You are also entitled to have the goods repaired
or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major
failure.
Should your Davey product require repair or service after the guarantee period; contact your nearest
Davey Dealer or phone the Davey Customer Service Centre on the number listed below.
For a complete list of Davey Dealers visit our website (davey.com.au) or call:
AUSTRALIA
Customer Service Centre
6 Lakeview Drive,
Scoresby, Australia 3179
Davey Water Products Pty Ltd
Ph:
Member of the GUD Group
Fax:
ABN 18 066 327 517
Website: davey.com.au
Email:
® Davey is a registered trademark of Davey Water Products Pty Ltd.
© Davey Water Products Pty Ltd 2015.
* Installation and operating instructions are included with the product when purchased new.
They may also be found on our website.
NEW ZEALAND
Customer Service Centre
7 Rockridge Avenue,
Penrose, Auckland 1061
1300 232 839
Ph:
0800 654 333
1300 369 119
Fax:
0800 654 334
Website: daveynz.co.nz
sales@davey.com.au
Email:
sales@dwp.co.nz
P/N 401575-8
Installation and
Operating Instructions
Pressure System Controller
NOTE: Prior to installation remove the inlet and outlet
pipe transport plugs & associated seals from the
suction and/or discharge ports.
WARNING : The Torrium2 controller, pump and associated pipework
operate under pressure. Under no circumstances should the Torrium2
controller, pump or associated pipework be disassembled unless the
internal pressure of the unit has been relieved. Failure to observe this
warning will expose persons to the possibility of personal injury and may
also result in damage to the pump, pipework or other property.
WARNING: Failure to follow these instructions and comply with all applicable
codes may cause serious bodily injury and/or property damage.
Please pass these instructions on to the operator of this equipment.
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Davey Torrium2
Summary of Contents for Davey Torrium2
- Page 1 Customer Service line on 1300 367 866 in Australia, or 0800 654 333 in New Zealand, or send a written letter to Davey at the address listed below. On receipt of your claim, Davey will seek to resolve your difficulties or, if the product is faulty or defective, advise you on how to have your Davey product repaired, obtain a replacement or a refund.
- Page 2 Your Torrium2 controller is designed to handle clean water. The system should not be used for any other purpose without specific referral to Davey. The use of the system to pump flammable, corrosive and other materials of a hazardous nature is specifically...
- Page 3 750kPa maximum shut-off head or dead head pressure. *’total system’ includes maximum incoming pressure and pump pressure (e.g. mains boosting) NOTE: While Torrium2 can be connected to pumps of nearly all single phase voltages commonly used worldwide, special models with power leads to suit particular regions or countries are made.
- Page 4 Hydrascan and Torrium flanges. First, fit the Torrium2 controller with the adaptor flange using a thread tape to seal, then fit the Torrium2 to the existing union nut on the pump. DO NOT OVERTIGHTEN! The control unit is capable of 360° rotation without loosening the nut, to enable the most convenient positioning of the discharge piping.
- Page 5 (R.O.) filter or similar low flow device, dealer. the Torrium2 will detect the limited demand. This will result in the Torrium2 3. Prime button has been held in for too long. Release prime button adapting to the slow demand. The pump start pressure will be allowed and switch off power for 1 minute to allow unit to reset.
- Page 6 Should the oring of the inbuilt check valve be removed though, an voltage at pump, excessive temperature (above 50°C) in pump enclosure. The Torrium2 controller may have to be reset after rectifying any of the above additional accumulator should be fitted to the Torrium2, or discharge operating troubles.
- Page 7 The electrical connections and checks must be made by a qualified electrician and comply with applicable local standards. The Torrium2 will generally be supplied with a three pin male power plug for connection to mains power and a terminated lead for connection to the motor.
- Page 8 ‘water return’ activated cycle power off / on To allow you to check the status of the inbuilt MOV in the Torrium2 there is a viewing window at the back of the Torrium2 above the power lead entry / exit grommet. The MOV is the blue disc shaped component. Should it be Only one fault condition will be indicated at once.
Need help?
Do you have a question about the Torrium2 and is the answer not in the manual?
Questions and answers