Page 2
Declaration of CE This product has passed the CE certification for environmental specifications. Test conditions for passing included the equipment being operated within an industrial enclosure. In order to protect the product from being damaged by ESD (Electrostatic Discharge) and EMI leakage, we strongly recommend the use of CE-compliant industrial enclosure products.
Activate Fault Alarm The JetCon 1701GP-U provides an alarm relay to trigger out a real alarm signal for power event. The alarm mechanism can be triggered by an external alarm equipment to inform maintenance I.T. engineers. It makes a...
1-2. Package Checklist JetCon 1701GP-U package includes the following items: JetCon 1701GP-U x1 One DIN-Rail clip (already screwed on the back of JetCon 1701GP-U x1 JetCon 1701GP-U Quick Installation Guide Contact your sales representative if any item is missing or damaged.1...
2-2. Front Panel The Front Panel of the JetCon 1701GP-U Industrial Gigabit PoE injector is shown in Figure A Figure A Power LED Alarm Relay Indicator LED for PoE Gigabit RJ-45 for 10/100/1000 Mbps...
Earth Ground Screw Terminal Block The power range of JetCon 1701GP-U is from DC 44~57V with redundancy and polarity reverse function. To prevent interference and get better performance, it is strongly suggest make a well earth grounding by the “Earth Ground Screw”.
2-4. Wiring the DC Power Inputs Follow the steps below to wire JetCon 1701GP-U redundant DC power inputs. [Note] The suitable electric wire ranges from 12 to 23 AWG. Insert the positive and negative wires into the V+ and V- contacts respectively of the terminal block connector Tighten the wire-clamp screws to prevent the DC wires from being loosened.
About the relay function, please refer section 4-4 2-6. LED Indicators The front panel of JetCon 1701GP-U includes 2 Power LEDs, 1 LED for Alarm Relay , 1 LED for PoE. Following table gives descriptions of the function for each LED indicator.
Status Description Green On Power 1 is supplying DC power. Power 1 No power is being supplied. Green On Power 2 is supplying DC power. Power 2 No power is being supplied. Amber On Output power is supplied Amber Off No output power Red on PW1 or PW2 is disconnect.
3. Mounting Installation 3-1. DIN-Rail Mounting The DIN-Rail clip is already attached on the rear side of JetCon 1701GP-U. JetCon 1701GP-U supports EN 50022 standard DIN Rail, in the following diagram includes the dimension of EN 55022 DIN Rail for your reference.
4. System Configuration The JetCon 1701GP-U provides Ethernet signal transfer function from electrical to optical and various packet handling and cable diagnostic features. In this chapter, we will introduce how to configure those functions and benefits as following topics. 4-1. Event Alarm Relay Configuration 4-1.
1. Take out your JetCon 1701GP-U Industrial Gigabit PoE Injector from the package box. 2. Check if the DIN-Rail clip is attached to the JetCon 1701GP-U. If the DIN-Rail clip is not attached to the JetCon 1701GP-U, refer to DIN-Rail Mounting section for DIN-Rail installation.
Page 15
to the network device’s Gigabit ethernet port. 9. Check the LED indicator of port status (blinking green) on the JetCon 1701GP- U to see if the network connection is successfully established. Power on the PC host, activate the Command Line mode, and ping the connected Ethernet device to see if it responds.
Page 16
13. Exit the Command Line mode, and connect PWR1 power input. At this stage, your JetCon 1701GP-U has been tested and the installation is completed.
6. Troubles shooting Make sure you are using the correct DC power suppliers (DC44~57 V) or power adapters. Select Ethernet cables with specifications suitable for your applications to set up your systems. Ethernet cables are categorized into unshielded twisted-pair (UTP) and shielded twisted-pair (STP) cables.
Page 18
7. Technical Specifications Technology Standard IEEE 802.3af Power over Ethernet IEEE 802.3at High Power PoE+ IEEE 802.3bt High Power PoE++ Performance Forwarding Store and Forward technology with 64~10K bytes packet forwarding ability Technology Event Alarm relay alarm output for power events PoE forwarding RJ-45: V-(1,2), V+ (3,6) for IEEE802.3 af/at conductor...
Page 19
IEC 61000-4-5, IEC 61000-4-6, IEC 61000-4-8, IEC 61000-4-11 Shock IEC60068-2-27 (Compliance) Vibration IEC60068-2-6 (Compliance) Free Fall IEC60068-2-32 (Compliance) Warranty 5 years Ordering Information JetCon 1701GP-U Industrial Gigabit PoE Injector Includes 1 x JetCon 1701GP-U Industrial one-port PoE Gigabit Injector 1 x Quick Installation Guide...
Page 20
Revision History Edition Date Modifications V1.0 16-Apr,2018 New edition V1.1 1-Nov. 2019 Correct Spec.
Need help?
Do you have a question about the JetCon 1701GP-U and is the answer not in the manual?
Questions and answers