Advertisement
Quick Links
1. PICTURE TUBE
Size
DefIection Angle
Neck Diameter
Solt Pitch
Face Treatment
2. SIGNAL
2-1. Horizontal & Vertical Sync
1) Input Voltage Level : Low= ≤0.8V, High= ≥2.1V
2) Sync Polarity
2-2. Video Input Signal
1) Voltage Level
a) Color 0, 0
b) Color 7, 0
c) Color 15, 0
2) Input Impedance
3) Video Color
4) Signal Format
2-3. Signal Connector
15 Pin D-Sub Connector
2-4. Scanning Frequency
Horizontal
Vertical
3. POWER SUPPLY
AC 100~240V, 50/60HZ, 2.5A Max.(Free Voltage)
AC 200~240V, 50Hz, 1.5A Max.(PFC version)
SPECIFICATIONS
: 17 inch (Flat Slot Mask)
: 90°
: 29.1 mm
: 0.24 mm
: W-ARASC (Anti-Reflective and
Anti-Static Coating),
Internal Anti-Glare
: Positive or Negative
: 0 ~ 0.7 Vp-p
: 0 Vp-p
: 0.467 Vp-p
: 0.7 Vp-p
: 75 Ω
: R, G, B Analog
: Refer to the Timing Chart
: 30 ~ 96 kHz
: 50 ~ 160 Hz
3-2. Power Consumption
MODE
H/V SYNC
NORMAL (ON)
ON/ON
STAND-BY
OFF/ON
SUSPEND
ON/OFF
OFF
OFF/OFF
4. DISPLAY AREA
4-1. Active Video Area :
• Max Image Size - 325.4 x 244.1mm (12.91" x 9.61")
• Preset Image Size - 310 x 230 mm (12.20" x 9.06")
4-2. Display Color
4-3. Display Resolution : 1600 Dots x 1200Lines / 75Hz
4-4. Video Bandwidth
5. ENVIRONMENT
5-1. Operating Temperature: 0°C ~ 40°C (32°F ~ 104°F)
5-2. Relative Humidity
5-3. Altitude
6. DIMENSIONS (with TILT/SWIVEL)
Width
Depth
Height
7. WEIGHT (with TILT/SWIVEL)
Net Weight
Gross Weight
POWER CONSUMPTION
LED COLOR
less than 84W
less than 8W
less than
8W
less than 3W
: Full Colors
: 207MHz
(Ambient)
: 10% ~ 90%
(Non-condensing)
: 10,000 ft
: 415 mm (16.34")
: 439 mm (17.28")
: 435 mm (17.13")
: 19.2 kg (42.34lbs)
: 22.5 kg (49.61 lbs)
GREEN
AMBER
Advertisement
Related Manuals for Fujitsu 17P4-FS792E
Summary of Contents for Fujitsu 17P4-FS792E
- Page 1 SPECIFICATIONS 1. PICTURE TUBE 3-2. Power Consumption Size : 17 inch (Flat Slot Mask) MODE H/V SYNC POWER CONSUMPTION LED COLOR DefIection Angle : 90° Neck Diameter : 29.1 mm NORMAL (ON) ON/ON less than 84W GREEN Solt Pitch : 0.24 mm STAND-BY OFF/ON less than 8W...
-
Page 2: General Information
ADJUSTMENT GENERAL INFORMATION 3) EEPROM → ALL CLEAR → Y(Yes) command. All adjustment are thoroughly checked and corrected when the monitor leaves the factory, but sometimes <Caution> Do not run this procedure unless the several adjustments may be required. EEPROM is changed. All data in EEPROM (mode Adjustment should be following procedure and after data and color data) will be erased. - Page 3 15) Adjust R-DRIVE and G-DRIVE command to white 8. Special PRESET Mode Adjustment Method with OSD control. balance x=0.283 ± 0.003 and y=0.298 ± 0.003 on Service man can adjust preset modes data easily by the White Balance Meter with PC arrow keys. OSD control key (select/Adjustment) on the monitor 16) Adjust SUB-CONTRAST command to 47±1FL of without any jig or program.
-
Page 4: Timing Chart
TIMING CHART VIDEO SYNC FACTORY PRESET MODE MODE MARK MODE 1 MODE 2 MODE 3 MODE 4 MODE 5 MODE 6 MODE 7 MODE 8 MODE 9 MODE 10 Sync Polarity — — — 53.674 63.000 80.8 79.976 68.677 91.150 93.750 31.469 31.472... - Page 5 < OSD Control > Heater ( 6.3V ) H / V POSITION Signal H / V SIZE H-Sync Sig Cable SPCC VIDEO VIDEO V-Sync Sig TRAPIZODE PRE-AMP MAIN AMP PIN BALANCE C DATA(SDA) (IC302) (IC303) PARALLELOGRAM C CLOCK(SCL) TILT TOP/BOTTOM CORNER RECALL MICOM CUT OFF...
-
Page 6: Description Of Block Diagram
DESCRIPTION OF BLOCK DIAGRAM 1. Line Filter & Associated Circuit. 5. X-ray Protection. This is used for suppressing noise of power input line This circuit detects the rectified DC voltage comes flowing into the monitor and/or some noise generated from the FBT pin 4. If the high voltage of the FBT in this monitor flowing out through the power input reaches up to about 30kV (abnormal state), H.V control (IC702) detects. - Page 7 11. D/D Drive & Convert Circuit. 19. Image Rotation (Tilt) Circuit. This circuit is used for supplying B + voltage to This circuit corrects the tilt of the screen by supplying horizontal deflection output transistor (Q708). This the image rotation signal to the tilt coil which is circuit makes to add side-pincushion correcting signal attached to the CDT near the deflection.
- Page 8 VR701 : High Voltage Adjustment VR901: B Adjustment (190V Line)
- Page 9 1. NO POWER NO POWER (POWER INDICATOR OFF) CHECK TROUBLE IN FUSE OK? FUSE (F901) CHECK TROUBLE IN D901 BRIDGE DIODE BRIDGE DIODE? (D901) CHECK C907(+) VOLTAGE TROUBLE IN 155VDC at 110V input IC901 310VDC at 220V input CHECK TROUBLE IN D912, D928 ? D912, D928 TROUBLE IN...
- Page 10 2. NO CHARACTER NO CHARACTER TROUBLE IN CHECK P301, SIGNAL CABLE, IC302 PIN 5, 6, 7 ? PC SIGNAL CHECK TROUBLE IN IC302 PIN 18, 19, 20, IC302, P302 PIN 9 (5V) ? CHECK IC303 PIN 1, 3, 5 TROUBLE IN PIN10 (12V), IC303 PIN 6 (80V) ?
- Page 11 3. NO RASTER NO VIDEO (POWER INDICATOR GREEN or AMBER) CHECK AMBER POWER INDICATOR TROUBLE IN GREEN or AMBER ? P302 SIGNAL CABLE GREEN MIN. ROTATE SCREEN CHECK (Counter-clockwise) CONTROL KNOB TO SCREEN CONTROL CLOCKWISE KNOB OF FBT CHECK VOLTAGE AT D912 CATHODE (190V) TROUBLE IN PRIMARY D928 CATHODE (80V)
-
Page 12: No Vertical Deflection
4. NO VERTICAL DEFLECTION NO V-DEFLECTION (ONE HORIZONTAL LINE) CHECK TROUBLE IN IC601 Pin 2 T901 PIN 15 (15V) ? CHECK TROUBLE IN IC601 PIN 4 T901 PIN 17, D907 (-12V)? CHECK TROUBLE IN IC701 PIN 13 IC701 (SAWTOOTH WAVE)? TROUBLE IN IC601, V-CIRCUIT... - Page 13 5. TROUBLE IN DPM STAND-BY/SUSPEND/ OFF MODE FAILURE CHECK CHECK PC, IC401 (MICOM) NO H / V SYNC SIGNAL (PC IS NOT GOING INTO PIN 40, 41 (H/V INPUT) DPM MODE) SIGNAL? INPUT H/V SYNC CHECK TROUBLE IN IC401 PIN 9, 8 X401, IC401 WAVEFORM? CHECK...
- Page 14 6. NO DEGAUSSING NO DEGAUSSING CHECK TROUBLE IN IC401 PIN 6 IC401 (MICOM) (5V)? CHECK TROUBLE IN Q908 COLLECTOR D914 VOLTAGE (0.5V)? CHECK TROUBLE IN P901? P901 CHECK TROUBLE IN RL901? RL901 TROUBLE IN TH901, DEGAUSSING COIL...
- Page 15 7. TROUBLE IN OSD NO OSD CHECK TROUBLE IN IC301 PIN 4 P302 (5V) ? CHECK IC301 PIN 5 TROUBLE IN (NEGATIVE H-PULSE P302 COMES IN ?) CHECK IC301 PIN 10 TROUBLE IN (V-PULSE COMES IN?) P302 CHECK IC301 PIN 13, 14, 15 TROUBLE IN (IS THERE ANY SIGNAL IC301, IC401...
- Page 16 Anode Cap DY-Pin DY Assembly Screw P303 P303 P302 P520 P701 Degaussing Coil P921 P901 P702 P401 P451 P453 P201...
- Page 18 #(4)CDT FIX 15-2 6140TC2015A COIL,DEGAUSSING, 1410MM 17.0OHM 0.5MM 130T 17"/95KHZ WITH EARTH 6871TCT092B PWB(PCB) ASSEMBLY,COMPOSITE, FS792E CONTROL TOTAL FUJITSU SIMENS CA-103 6174Z-1042B FBT (FLY BACK TRANSFORMER), FMMTC94 AM1042B (LIM SANG IL) 6200TJB001J FILTER(CIRC), EMC, 02MD1-1 DELTA BK WITH GND 4951TKK028E...