Philips AZ1330D User Manual

Docking Entertainment System
User manual
Meet Philips at the Internet
http://www.philips.com
W
CLASS 1
LASER PRODUCT
AZ1330D
Printed in China PDCC-JH-0721
AZ1330D
Hearing Safety
Listen at a moderate volume.
• Using headphones at a high volume can impair your hearing. This product can produce sounds in
decibel ranges that may cause hearing loss for a normal person, even for exposure less than a
minute. The higher decibel ranges are offered for those that may have already experienced some
hearing loss.
• Sound can be deceiving. Over time your hearing "comfort level" adapts to higher volumes of
sound. So after prolonged listening, what sounds "normal" can actually be loud and harmful to
your hearing. To guard against this, set your volume to a safe level before your hearing adapts and
leave it there.
To establish a safe volume level:
• Set your volume control at a low setting.
• Slowly increase the sound until you can hear it comfortably and clearly, without distortion.
Listen for reasonable periods of time:
• Prolonged exposure to sound, even at normally "safe" levels, can also cause hearing loss.
• Be sure to use your equipment reasonably and take appropriate breaks.
Be sure to observe the following guidelines when using your headphones.
• Listen at reasonable volumes for reasonable periods of time.
• Be careful not to adjust the volume as your hearing adapts.
• Do not turn up the volume so high that you can't hear what's around you.
• You should use caution or temporarily discontinue use in potentially hazardous situations.
• Do not use headphones while operating a motorized vehicle, cycling, skateboarding, etc.; it may
create a traffic hazard and is illegal in many areas.
NOTES
1
#
AUX DOCK
@
DOCKING ENTERTAINMEN T S YSTE M A Z1330 D
!
DOCK FOR
for
DBB VOLUME
0
9
8
6 x R20 • UM-1 • D-CELLS
%
MP3 -WMA PLAYBACK
^
iR
*
& (
@
¡
) 8
™
6
£
7 4
≤ ∞
8
2
3
X
4
5
6
9
7
1
English Controls / Power Supply
1
For Tuner:
Supplied accessories
– tunes to a radio station
– AC power cord
9 – stops disc playback;
– Remote control
– erases a program
– Docking kit
2
DBB – turns on/off bass enhancement
• 1 x Apple iPod dock (pre-installed with the
@ p – 3.5 mm stereo headphone socket
main set)
3 Helpful hints: The speakers will be muted
• dock adaptors (8 adaptors for different iPod
when headphones are connected to the set.
types)
4
# AUX jack – connects an external source
• 1 dust cover (keep the dock connector
5
from covering dust and dirt)
$ Battery door – opens to insert 6 x 1.5V
• Line-in cable
6
7
Top and front panels (See 1) % Disc tray – load a disc
^ iR – infrared sensor for remote control
1 Telescopic antenna – improves FM
$ reception
Remote control (See 1)
2 DOCK – selects dock source
3 Dock connector – connects iPod player & CD – selects disc mode
* TUNER – selects tuner mode
4 VOLUME/VOL +/- – adjusts volume level
( DOCK – selects dock (iPod) source
5 MODE – selects different play modes:
) AUX– selects AUX mode
e.g. REPEAT or SHUFFLE (random
¡ 9 – stops disc playback;
order)
– erases a program
6 PROGRAM
™ REPEAT – repeats a track/disc/all
For disc – programs tracks and reviews the
program
£ SHUFFLE – turns on/off the random play
For Tuner – auto searches and stores radio
stations
≤ DBB – turns on/off bass enhancement
7 ALBUM/PRESET +/- ( 3, 4 )
∞ MUTE –mutes or restores the volume
For MP3-CD/ WMA play:
– select albums
Power Supply
For Tuner
Whenever convenient, use the power supply
– selects a preset radio station
cord if you want to conserve battery life.
8 / – opens/closes the disc tray
Make sure you remove the plug from the set
9 SOURCE: – selects CD/MP3-CD, DOCK
and wall outlet before inserting batteries.
mode,Tuner or AUX
Batteries
0 POWER – powers on/off the system
Main set (See 1)
! 2; – starts or pauses disc/DOCK playback
∞ § • Insert 6 batteries, type R-20, UM1 or D-
cells (not included, preferably alkaline) with
For disc/ DOCK play:
the correct polarity.
– skips to the beginning of a current/
previous/ later track
– fast searches backwards and forwards
within a track
Power Supply
Remote control • Disconnect the power cord from the wall
Important! socket to protect your set during heavy
thunderstorms. Children could seriously injure
• Before using the remote control, remove
themselves as the free end of the cable may
the insulation plastic tab as shown
in figure 9. still be live if only the connector is removed
• If the remote control does not function from the MAINS socket at the back of the
unit.
correctly or the operating range is
reduced, replace the battery with a new
(CR2025) type battery.
The type plate is located on the
bottom of the set.
1 Pull the battery tray out as shown
in figure 9.
Auto power saving
2 Replace a new battery according to polarity
• In CD and DOCK mode, if AZ1330D is in
indication, and fully insert the battery tray
the PAUSE position for 5 minutes, it will auto
back to the original position.
switch to the stop position.
• Incorrect use of batteries can cause
• In CD and DOCK mode, if AZ1330D is in
electrolyte leakage and will corrode the
the STOP position for 15 minutes, it will auto
compartment or cause the batteries to burst:
switch to standby to save power.
• Do not mix battery types: e.g. alkaline with
Helpful hints:
carbon zinc. Only use batteries of the same
type for the set. – To avoid unnecessary energy consumption,
always press POWER on the set to power
• When inserting new batteries, do not try to
off the set after using the set.
mix old batteries with the new ones.
• Remove the batteries if the set is not to be
CAUTION
used for a long time.
Batteries contain chemical substances, so
- Visible and invisible laser radiation.
they should be disposed of properly. If the cover is open, do not look at
the beam.
Using AC power
- High voltage! Do not open.You run
1 Check if the power/mains voltage, as shown the risk of getting an electric
on the type plate located on the shock.The machine does not con-
bottom of the set, corresponds to your
tain any user-serviceable parts.
local power supply. If it does not, consult your
- Modification of the product could
dealer or service center.
result in hazardous radiation of
2 Connect the power cord to the
EMC or other unsafe operation.
AC~ MAINS inlet and the wall socket.The
set is now ready for use.
3 To switch the set off completely, withdraw
the power cord from the wall socket.
2
3
4 Install the unit near the AC outlet and where
the AC power plug can be easily reached.
(3.5 mm socket)
R-20/ -UM1/ D-cells
programmed tracks
mode