Advertisement
Quick Links
Instructions
Pro-Shot
Dispense Valve
For high pressure grease dispense. For professional use only.
Model No. 242055, Series B, 1/4 npt Fluid Inlet
Model No. 242056, Series B, 1/4 npt Fluid Inlet with Coupler
Model No. 242057, Series B, 3/8 npt Fluid Inlet
Model No. 242058, Series B, 3/8 npt Fluid Inlet with Coupler
Model No. 24H399, Series A, 1/4-19 bspt Fluid Inlet
Model No. 24H400, Series A, 1/4-19 bspt Fluid Inlet with Coupler
Model No. 24H401, Series A, 3/8-19 bspt Fluid Inlet
Model No. 24H402, Series A, 3/8-19 bspt Fluid Inlet with Couple
Model No. 24H403, Series A, 1/4-19 bspp Fluid Inlet
Model No. 24H404, Series A, 1/4-19 bspp Fluid Inlet with Coupler
Model No. 24H405, Series A, 3/8-19 bspp Fluid Inlet
Model No. 24H406, Series A, 3/8-19 bspp Fluid Inlet with Coupler
8000 psi (55.2 MPa, 552 bar) Maximum Working
Pressure
Important Safety Instructions
Read all warnings and instructions in this
manual. Save these instructions.
™
Grease
.
Get other manuals https://www.bkmanuals.com
309032L
EN
Advertisement
Related Manuals for Graco Pro-Shot A Series
Summary of Contents for Graco Pro-Shot A Series
- Page 1 Instructions ™ Pro-Shot Grease Dispense Valve 309032L For high pressure grease dispense. For professional use only. Model No. 242055, Series B, 1/4 npt Fluid Inlet Model No. 242056, Series B, 1/4 npt Fluid Inlet with Coupler Model No. 242057, Series B, 3/8 npt Fluid Inlet Model No.
- Page 2 Warnings Warnings The following warnings are for the setup, use, grounding, maintenance, and repair of this equipment. The exclama- tion point symbol alerts you to a general warning and the hazard symbols refer to procedure-specific risks. When these symbols appear in the body of this manual or on warning labels, refer back to these Warnings. Product-specific hazard symbols and warnings not covered in this section may appear throughout the body of this manual where applicable.
-
Page 3: Operation
Operation Operation Pressure Relief Procedure NOTE: If you suspect the dispensing valve, extension, or grease fitting coupler is clogged, or the pressure has not been fully relieved after following the previous steps, Follow the Pressure Relief Procedure whenever using a rag VERY SLOWLY loosen the coupler or hose you see this symbol. -
Page 4: Troubleshooting
Service Service Refer to Parts Drawing, page 5, for following instruc- 9. Push plunger rod (15) through seal (4). Be careful; tions. seat (14), ball (2), and copper gasket (6) will fall out bottom. 10. Replace all parts included in service kit 243446. Disassembly 11. -
Page 5: Technical Data
Parts Parts Ref. Part Description Qty. Ref. Part Description Qty. 16G884 ADAPTER, 1/4”-19 bspt, seat, † NUT, self-locking, 10-32 model 24H399 and 24H400 † BALL, carbide 16G885 ADAPTER, 1/4”-19 bspp, seat, † SPRING, compression † SEAL model 24H403 and 24H404 †... -
Page 6: Graco Standard Warranty
With the exception of any special, extended, or limited warranty published by Graco, Graco will, for a period of twelve months from the date of sale, repair or replace any part of the equipment determined by Graco to be defective.