Cleaning, Maintenance And Ordering Of Spare Parts; Disposal And Recycling - EINHELL IMPAXXO 18/400 Original Operating Instructions

Fitting / removing the plug-in tool
Fit the required drive socket insert by pushing
onto the square drive mount (1).
Remove the drive socket insert by pulling it off the
square drive mount (1).
6.7 Selector switch setting 1-2-3
(Fig. 7/Item 2)
There are 3 settings for operating the cordless im-
pact driver. This enables you to adjust the speed
and torque to the specifi c size of screw.
To move from one setting to another, press briefl y
on the selector switch setting 1 - 2 - 3 (2).
The active setting of the impact driver is indicated
by the 3 LEDs (f).
Setting 1: Low speed / torque
Setting 2: Medium speed / torque
Setting 3: Maximum speed / torque
6.8 Working with the impact driver
Loosening:
•
Mount a drive socket insert on the impact dri-
ver (see point 6.6).
•
Place the impact driver on the screw/nut and
loosen the screw/nut by pressing the On/Off
switch (4).
•
If the screws/nuts are very tight or if they are
rusted, use a tire wrench or torque wrench to
slightly loosen them.
Tightening:
•
Warning! Use the impact driver only for
loosening screws/nuts. If you want to use the
impact driver to tighten screws and nuts, you
must also use a torque limiter which is desig-
ned for this purpose. If not, the screw connec-
tion may be damaged. The torque limiter is
available from your dealer. It is not included in
the scope of this delivery.
•
Prior to tightening, carefully insert the screw/
nut into the threads.
•
It is important that screws/nuts with special
torque specifications (for example provided
by the vehicle manufacturer in the automoti-
ve sector) are tightened only with a suitable
torque limiter.
Hazard!
Screws/nuts must be fi nish-tightened with a
torque wrench which is set to the torque speci-
fi ed by the manufacturer and then they must be
checked!
Anl_IMPAXXO_18_400_SPK7_THA.indb 15 Anl_IMPAXXO_18_400_SPK7_THA.indb 15
EN
7. Cleaning, maintenance and
ordering of spare parts
Danger!
Always remove the battery pack before making
adjustments to the equipment.
7.1 Cleaning
•
Keep all safety devices, air vents and the
motor housing free of dirt and dust as far as
possible. Wipe the equipment with a clean
cloth or blow it with compressed air at low
pressure.
•
We recommend that you clean the device
immediately each time you have finished
using it.
•
Clean the equipment regularly with a moist
cloth and some soft soap. Do not use
cleaning agents or solvents; these could at-
tack the plastic parts of the equipment. Ensu-
re that no water can seep into the device. The
ingress of water into an electric tool increases
the risk of an electric shock.
7.2 Maintenance
There are no parts inside the equipment which
require additional maintenance.
7.3 Ordering spare parts and accessories
Please contact the dealer that near home or
contact through company www.zinsano.com
LINE : @zinsano
or scan this QR Code

8. Disposal and recycling

The equipment is supplied in packaging to pre-
vent it from being damaged in transit. The raw
materials in this packaging can be reused or
recycled. The equipment and its accessories are
made of various types of material, such as metal
and plastic. Never place defective equipment in
your household refuse. The equipment should
be taken to a suitable collection center for proper
disposal. If you do not know the whereabouts of
such a collection point, you should ask in your
local council offi ces.
- 15 -
07.07.2023 09:30:26 07.07.2023 09:30:26