Voltage/Phase Availability; Important Safety Instructions; Releasing Disposer Jam - InSinkErator SS100-28 Operating Instructions

Model Voltage, Hz
SS100-28 115/208/230V
SSC100-1 115/208/230V
SS100-35 100/200/230V, 50/60Hz
SS100-47 208/230/460V, 60Hz
SSC100-3 208/230/460V, 60Hz
SS100-50 208-230/460/3
SS200-27 115/208/230V
SS200-31 115/208/230V
SSC200-1 115/208/230V
SS200-35 208/230/460V, 60Hz
SS200-36 208/230/460V, 60Hz
SS200-39 380/50-60Hz
SSC200-3 208/230/460V, 60Hz
SS300-21 415 V
SS300-22 220 V
SS300-23 380V, 50/60Hz
SS300-25 208/230/460V, 60Hz
This appliance is not intended for use by persons
(including children) with reduced physical sensory
or mental capabilities, or lack of experience and
knowledge, unless they have been given supervision
or instruction concerning use of the appliance by a
person responsible for their safety.
Children should be supervised to ensure that they
do not play with the appliance.
DO NOT operate without factory-recommended
safety guards.
DO NOT put your hands into the disposer while it is
in operation.
Switch off or unplug the appliance before attempting
to free a jammed rotor with an implement.
If the disposer stops suddenly it may be
due to overloading or a foreign object
(metal) has caused a jam condition.
Turn control to off position and complete
following steps:
1. Insert dejamming wrench (not
supplied) slot down through sink
opening. Place slot over raised bars
found on top of rotating shredder.

VOLTAGE/PHASE AVAILABILITY

Phase
Model
1Ph
SS300-27
1Ph
SS500-22
1Ph
SS500-23
3Ph
SS500-27
3Ph
SS500-28 208/230/460V, 60Hz
3Ph
SS500-30
1Ph
SSC500-1
1Ph
SS1000-10 208/230/460V, 60Hz
1Ph
3Ph
SS1000-12
3Ph
3Ph
3Ph
3Ph
3Ph
3Ph
3Ph

IMPORTANT SAFETY INSTRUCTIONS

RELEASING DISPOSER JAM

2. Twist dejamming wrench back and
forth to free jam. Rotating shredder
should revolve freely when jam is
released.
3. Remove all foreign materials.
4. Allow disposer to cool for 3-5 minutes
after it stops running. Press red reset
button to reset overload protector.
Never strike reset button with objects.
5. If disposer remains inoperative after
following these steps, contact nearest
InSinkErator Factory Authorized
Service Center.
Voltage, Hz Phase
208/230/460V 3Ph
230/460V 3Ph
415V 3Ph
380V 3Ph
3Ph
208/230/460V 3Ph
208/230/460V 3Ph
3Ph
208/230/460V 3Ph
• DO NOT put any of the following items into the
disposer: clam or oyster shells, drain cleaner, glass,
china, plastic wrap, large bones, metal objects,
explosive materials, extremely hot water, grease, oil,
or syrup.
• DO NOT overload disposer with excess amounts of
food waste and water. The unit will consume food
waste faster when you feed it steadily.
• DO NOT touch the water valve after the correct flow
of water is achieved by adjusting plumbing valves.
Grinding efficiency will be decreased if the water
swirl is more than 1/2 way up the disposer body.
• DO NOT stop disposer with food waste in it; let it
run for approximately three (3) minutes to clear itself
of all ground waste. This will help maintain a clean
and odor-free unit and avoid drainline stoppage.
1-800-845-8345
Call
Service Center nearest you.
to find