Related Manuals for HG E1000 HIGH TIP
Summary of Contents for HG E1000 HIGH TIP
-
Page 1: User Manual
User Manual HG E1000 HIGH TIP USER MANUAL HG E1000 HIGH TIP SUPER SKUB HG Machines ApS hg-machines.com hello@hg-machines.com Side 1... -
Page 2: Table Of Contents
User Manual HG E1000 HIGH TIP Table of Contents User Manual ................................1 Introduction ................................. 3 1.Safety instruction ............................... 4 1.1 Read the manual ............................4 1.2 Education ..............................5 1.3 The most common causes of accidents are ....................5 1.4 Preparation .............................. -
Page 3: Introduction
User Manual HG E1000 HIGH TIP Introduction Manufacturer: The HG E1000 High Tip is an electrical, high- quality dumper with an added benefit – the HG Poland Sp. Z. O. O. ability to unload directly over the rim and into... -
Page 4: Safety Instruction
Next to a text in the manual highlights a risk of motor must be switched off, the ignition key injury if users do not follow the instructions removed and the main switch turned off. At HG, we always recommend qualified WARNING! staff/workshops for servicing and Hot parts troubleshooting. -
Page 5: Education
• Ensure that he machine is adequately The operator should be given adequate charged. HG does not recommend driving instructions for using the motor barrow. These with less than 15% battery capacity. instructions should focus on: •... -
Page 6: Noise And Vibration Level
The uncertainty of the above measurements is ± 2 dB. HG recommends the use of hearing protection, even if the noise is below the statutory limit. Vibration level According to ISO 1032, the maximum weighted... -
Page 7: Operation
User Manual HG E1000 HIGH TIP center of gravity of the motor barrow is 1.6 Operation higher when the skip is full. WARNING! Do not use the motor Failure to observe the following operating barrow with insufficient instructions may result in injury: ceiling height. -
Page 8: Maintenance
User Manual HG E1000 HIGH TIP • When leaving the motor barrow, remove the 1.7 Maintenance ignition key and turn off the main switch. Each time the machine is used, visual inspection • Always turn off the ignition and main switch... -
Page 9: Transport & Towing
User Manual HG E1000 HIGH TIP WARNING! Always fit the safety bracket of the tipping cylinder before starting the inspection NOTE: The release handle must always be work. pushed up during normal operation, as the brake is otherwise disengaged When lifting the machine, the three attachment points on the front and on the instrument panel must be used. -
Page 10: Disposal & Dismantling
User Manual HG E1000 HIGH TIP The machine may only be transported with means of transport with sufficient ground clearance, as there is a risk of serious injury to the operator/damage to the machine and means of transport During transportation, the machine must be attached to the load surface or cargo hold in accordance with relevant regulations. -
Page 11: Charging And Storage
User Manual HG E1000 HIGH TIP the machine you can see the indicator lights on 2. Charging and the charger. During charging, the yellow lamp on Storage the charger will flash. See figure item 16. 2.1 Charging 1) Switch off the machine at the main switch, see figure pos. -
Page 12: Storage
The In conditions where a machine is to be stored container must be so long that there is no without operation for a longer period, HG possibility of tipping back accidentally. recommends that the machine's battery pack be placed in "storage mode"... - Page 13 User Manual HG E1000 HIGH TIP The top plate for the battery compartment is operation ready level mode. However, the then removed by lifting into the elongated hole. battery must be inspected every 2.5 months and The plate is held in place by magnets. See recharged to a minimum of 40%.
-
Page 14: Functions
User Manual HG E1000 HIGH TIP 3. Functions 3.1 Instrument panel 1) Operating push buttons for HIGH TIP 4) Signal horn. When the horn is pressed, it function. If the left button is pressed and emits a loud noise. The horn is used, for held, the container will lift. -
Page 15: The Machine's Functional Units
See figure pos. 10. Main switch seen in switched off position. When using the machine the main switch is rotated 90º clockwise. HG recommends using the turned-off position when the machine is not used for a HG Machines ApS hg-machines.com hello@hg-machines.com... - Page 16 User Manual HG E1000 HIGH TIP Side tipping of container. To facilitate accessibility of the machine's internal parts, the container can be advantageously tipped to the side by loosening the two bolts on the left side of the machine. See figure pos. 17.
- Page 17 User Manual HG E1000 HIGH TIP raised HIGH TIP or only tipped container is that the container can thereby be placed directly on the surface on which the machine stands. See figure pos. 28. If the HIGH TIP is not raised, the container,...
-
Page 18: Precautions Before Starting
User Manual HG E1000 HIGH TIP 4. Precautions before 4.1 Tire pressure and tension starting To achieve optimal ergonomic conditions, all Visual inspection of the machine. Make sure the tires must have the correct air pressure. machine and all warning pictograms are intact. - Page 19 User Manual HG E1000 HIGH TIP Safety plate test The safety plate must activate forward travel upon impact, so that the operator is not pinched in connection with reversing/reversing. NOTE: Before the test is started, a free space of at least 15 meters must be ensured all the way around the machine.
-
Page 20: Driving
HG E1000 HIGH TIP Check via the battery status that the machine is 5. Driving sufficiently charged. HG does not recommend driving with current below 10%, as this can Turn the main switch damage and shorten the life of the batteries. -
Page 21: Operation Of High Tip
User Manual HG E1000 HIGH TIP The direction is controlled by pulling the steering position, when the container cannot be lowered handle to the right or left during propulsion. Do any further, release the contact again. See not try to control the direction while the machine figure pos. -
Page 22: Maintenance
User Manual HG E1000 HIGH TIP 6. Maintenance = To be replaced when the machine has First run for 20 hours. three months. All maintenance must be performed by a qualified mechanic, service technician or similar Components must be inspected according to the supplier's recommendations. -
Page 23: Towing And Side Tipping Of The Container During Maintenance, Service, Engine Failure, Hydraulic Failure Or Power Failure
Alternatively, the machine's container can also be tipped without the HIGH TIP being raised, HG does not recommend leaving the however it is recommended that the HIGH TIP is machine in disconnected mode. -
Page 24: Maintenance Points
User Manual HG E1000 HIGH TIP The advantage of a raised HIGH TIP or only tipped container is that the container can thereby be placed directly on the surface on which the machine stands. See figure pos. 28. If the HIGH TIP is not raised, the container, when... - Page 25 User Manual HG E1000 HIGH TIP Filling hydraulic oil Remove the top plate for the battery When filling with hydraulic oil, the container must compartment and empty the compartment of be tipped to the side figure pos. 28, follow the foreign bodies such as sand, soil etc.
- Page 26 User Manual HG E1000 HIGH TIP Lubrication Air pressure in wheels Ordinary high-pressure grease can be used for To achieve optimal ergonomic conditions, all lubrication. There are grease nipples on: tyres must have the correct air pressure: • Driving wheels: 53 psi/3.7 bar Steering wheels 2 pcs.
- Page 27 User Manual HG E1000 HIGH TIP Replacement of signs Warning and control signs must be replaced if Safety plate adjustment they are difficult to read. Warning signs and Loosen the two lock nuts with a 13 mm wrench. pictograms must be fully intact and legible.
-
Page 28: Faq
User Manual HG E1000 HIGH TIP 7. FAQ Error Possible cause Possible cause The machine is not turned on or lacks Check main switch, ignition key, activation The machine will not start power. button is lit green and battery indicator. -
Page 29: Hydraulic Diagram And Electrical Diagram
User Manual HG E1000 HIGH TIP Lights up in the display, but only when Main relay broken or full of dirt Possible cause the activation button is pressed. Then the lamp immediately goes out again The device should be closer to the power... -
Page 30: Technical Specifications
User Manual HG E1000 HIGH TIP 9. Technical specifications Specifications Width 850 mm Length 2050 mm Height 1080 mm Net weight 455 kg Content in liters 400 L Contents in kg 1000 kg Chute height 125 cm Driving speed, 0-6 km/t... -
Page 31: Warranty
The manufacturer's approval of a claim for Warranty period compensation requires that the defective part is HG Machines provides a guarantee for 12 shown to the manufacturer or its representative months. The warranty period begins on the date within two weeks after the damage has of delivery. -
Page 32: Eu Declaration Of Conformity
User Manual HG E1000 HIGH TIP 11. EU declaration of conformity Hedensted, 15. Februar 2023 HG Machines ApS Vejlevej 15 DK-8722 Hedensted Nikolaj Birkerod Tel. (+45) 75 89 12 44 Adm. Direktør www.hg-machines.com Erklærer hermed, at: Super Skub model E1000 Typenummer 280200...
Need help?
Do you have a question about the E1000 HIGH TIP and is the answer not in the manual?
Questions and answers