Subscribe to Our Youtube Channel
Related Manuals for HG E1000
Summary of Contents for HG E1000
-
Page 1: User Manual
USER MANUAL HG E1000 USER MANUAL HG E1000 SUPER SKUB HG Machines ApS hg-machines.com hello@hg-machines.com Side 1... -
Page 2: Table Of Contents
USER MANUAL HG E1000 Table of Contents User Manual: ................................1 Introduction ................................3 1. Safety instructions ............................4 1.1 Read the manual ............................4 1.2 Education ..............................5 1.3 The most common causes of accidents are ....................5 1.4 Preparation ..............................5 1.5 Noise and vibration level .......................... -
Page 3: Introduction
USER MANUAL HG E1000 Introduction The HG E1000 is built for professional use in Manufacturer demanding urban environments. The high- quality dumper is user and service friendly and HG Machines ApS +45 75 89 12 44 has been well known for its longevity since hello@hg-machines.com... -
Page 4: Safety Instructions
Next to a text in the manual highlights a risk of removed and the main switch turned off. injury if users do not follow the instructions At HG, we always recommend qualified staff/workshops for servicing and WARNING! troubleshooting. -
Page 5: Education
• Ensure that he machine is adequately Remember that the operator is responsible for charged. HG does not recommend driving any accidents or hazardous situations that may with less than 15% battery capacity. occur involving other people or their property. -
Page 6: Noise And Vibration Level
• As far as possible, only use the motor 2 dB. barrow in daylight or in good artificial HG recommends the use of hearing protection, lighting. even if the noise is below the statutory limit. Vibration level According to ISO 1032, the maximum weighted... - Page 7 USER MANUAL HG E1000 • Do not use the motor Unloading of frozen loads or highly adhesive barrow with materials such as clay must not be insufficient ceiling height. performed by tipping, as the machine may tip over. • Driving on soft, loose and uneven surfaces is...
-
Page 8: Maintenance
USER MANUAL HG E1000 • When reversing, the That the motor barrow is stationary when the operator must pay propulsion lever is not activated. special attention to uneven surfaces and objects that the • That the safety plate activates forward operator may fall over or drive into. -
Page 9: Transport & Towing
USER MANUAL HG E1000 detachment cannot take place. 1.8 Transport & Towing In order for the machine to be towed without the motor being started, the release button on the right side below the control panel must be activated. The traction wheels are released and the machine can be moved. -
Page 10: Disposal & Dismantling
HG E1000 1.9 Disposal & Dismantling When, many years from now, the motor barrow is worn out and has to be disposed of, HG Machines will perform the dismantling by agreement, as this should take place in an environmentally sound manner. During... -
Page 11: Charging And Storage
USER MANUAL HG E1000 2. Charging and Storage 2.1 Charging 1) Switch off the machine at the main switch, see figure pos. 11. 4) Check that the machine is charging the battery. On the right side of the machine, seen... -
Page 12: Storage
See figure pos. 19 2.2 Storage In conditions where a machine is to be stored without operation for a longer period, HG recommends that the machine's battery pack be placed in "storage mode" and with a minimum of 40% power on the battery pack. - Page 13 USER MANUAL HG E1000 The machine is now ready for storage and will automatically go into "storage mode" as it will not register any discharge. In "storage mode" the battery pack will only consume 1-2% of operation ready level mode. However, the battery must be inspected every 2.5...
-
Page 14: Functions
USER MANUAL HG E1000 3. Functions 3.1 Instrument panel movement so the operator does not 1. Control handle for tipping the skip. risk getting trapped. Press up to tip, and down to lower 5. Control lever for reversing. The the truck bed. -
Page 15: The Machine's Functional Units
90º started. If the machine is not clockwise. HG recommends using the turned-off operated for 5 minutes, the machine position when the machine is not used for a will shut down and the button must longer period, e.g. - Page 16 USER MANUAL HG E1000 For charging, the charging connection is located behind the door. The charger can be connected to 16-30A group 220V . The plug is of the type is of the type 16A 2P+E Male type F. See figure pos.
-
Page 17: Precautions Before Starting
USER MANUAL HG E1000 Remove the top plate for the battery 4. Precautions before compartment and visually inspect the battery starting packs and make sure that they are tightened so that they cannot move during driving. Tighten Visual inspection of the machine. Make sure that the battery stops if necessary. - Page 18 USER MANUAL HG E1000 Safety plate test The safety plate must activate forward travel upon impact, so that the operator is not pinched in connection with reversing/reversing. NOTE: Before the test is started, a free space of at least 15 meters must be ensured all the way around the machine.
- Page 19 If the machine creeps slightly, it must be Check via the battery status that the machine is immediately removed from operation and the sufficiently charged. HG does not recommend fault must be rectified. driving with current below 10%, as this can damage and shorten the life of the batteries.
-
Page 20: Driving
HG does not recommend leaving the machine in the disengaged state. 6. Towing and side In case of motor failure, the skip can be tipped tipping the container up manually. - Page 21 USER MANUAL HG E1000 One person now holds the load up, while the other person mounts the safety bracket on the hydraulic cylinder. WARNING! There is now a vacuum in the cylinder. Activate the tipping lever with the machine on to refill before removing the safety bracket.
-
Page 22: Maintenance
USER MANUAL HG E1000 7. Maintenance First To be replaced when the machine has run for 20 hours Components must be inspected according to the supplier's recommendations. Hedensted Gruppen prescribes a major service inspection of the machine at least once per year, performed by a qualified service technician. -
Page 23: Maintenance Points
USER MANUAL HG E1000 The main switch is turned to the position shown 7.1 Maintenance Points to cut off the power from the battery pack to the other electrical components of the machine. Safety bracket Before starting maintenance work, the safety bracket must be installed on the tipping cylinder. - Page 24 USER MANUAL HG E1000 Remove the top plate for the battery compartment and empty the compartment of foreign bodies such as sand, soil etc. If necessary, use an industrial vacuum with a plastic suction attachment (NOT METAL or other conductive material). Avoid contact with the battery terminals.
- Page 25 USER MANUAL HG E1000 Lubrication Retensioning of wheels Ordinary high-pressure grease can be used for Tighten wheels once a week. lubrication. Tightening torque: 100 Nm. Replacement of signs Warning and control signs must be replaced if they are difficult to read. Warning signs and There are grease nipples on: pictograms must be fully intact and legible.
- Page 26 USER MANUAL HG E1000 Safety plate In the event of an impact, the safety plate must activate forward travel so that the operator is not crushed in connection with reversing. When the machine has moved away from the operator, it must stop again.
-
Page 27: Faq
The centrifugal clutch is worn. clutch. The steering wheel or suspension is The machine does not drive straight. Replace the wheel or suspension. damaged and steers unevenly. 9. Hydraulic diagram and electrical diagram Contact HG for diagram. HG Machines ApS hg-machines.com hello@hg-machines.com Side 27... -
Page 28: Technical Specifications
USER MANUAL HG E1000 10. Technical specifications Specifications Width 850 mm Length 2050 mm Height 980 mm Net weight 376 kg Content in liters 400 L Contents in kg 1000 kg Chute height 60 cm Driving speed, 0-6 km/t forward... -
Page 29: Warranty Provisions
Warranty period within two weeks after the damage has HG Denmark APS provides a guarantee for 12 occurred. Owner rights to the damaged part(s) months. The warranty period begins on the date are transferred to the supplier of the new parts. -
Page 30: Eu Declaration Of Conformity
Nikolaj Birkerod Tel. (+45) 75 89 12 44 Adm. Direktør www.hg-machines.com Hereby declares that: Super Skub model E1000 Type number 280200 Super Skub model E1000 Type number 280205 Super Skub model E1000 Type number 280210 Complies with: Machinery Directive 2006/42/EC...
Need help?
Do you have a question about the E1000 and is the answer not in the manual?
Questions and answers