User Manual HG H1000 HIGH TIP Table of Contents User Manual ................................1 Introduction ................................3 1.Safety ................................. 4 1.1 Read the manual ............................4 1.2 Education..............................5 1.3 The most frequent causes of accidents:..................... 5 1.4 Preparation ..............................5 1.5 Noise and vibration level ..........................6 1.5.1 Vibration level ............................
User Manual HG H1000 HIGH TIP Introduction Manufacturer: The HG H1000 High Tip HG Machines ApS is a high-quality dumper with an Vejlevej 15, 8722 added benefit – the ability to Hedensted, Danmark unload directly over the rim and Bredgade 63 A into containers and trailers.
User Manual HG H1000 HIGH TIP WARNING! 1.Safety Poisonous gases 1.1 Read the manual Do not let the engine run without Please read this manual carefully and make adequate ventilation and sure that it is also read by other potential never indoors, as the machine's exhaust users of the machine.
User Manual HG H1000 HIGH TIP 1.2 Education The operator's knowledge of the vehicle is insufficient • Read the instructions carefully. Please Too steep terrain conditions familiarize yourself with all controls, Substrate does not have sufficient switches etc. and how to use the stability equipment correctly.
87 dB (A) in accordance with ISO 6396. The uncertainty of the measurements stated above is ±2 dB. HG recommends the use of hearing protectors, even though the noise level is below the limit where hearing protection is required.
User Manual HG H1000 HIGH TIP center of gravity of the motor barrow is 1.6 Operation higher when the skip is full. WARNING! Do not use the motor Failure to observe the following operating barrow with insufficient instructions may result in injury: ceiling height.
Page 8
User Manual HG H1000 HIGH TIP • When leaving the motor barrow, remove the ignition key and turn off the main switch. • Always turn off the ignition and main switch before carrying out any service or repair works. •...
User Manual HG H1000 HIGH TIP 1.7 Maintenance Each time the machine is used, visual inspection and inspection must be performed to ensure: • That there are no leaks in the hydraulic system by hoses, tank etc. • That there are no worn or damaged cables.
User Manual HG H1000 HIGH TIP 1.8 Transport & towing Disposal & dismantling To tow the machine without starting the engine, When, many years from now, the motorized activate the coasting button on the left-hand wheelbarrow is worn out and must be disposed side.
User Manual HG H1000 HIGH TIP 2. Function description Instrument panel 1) Operating handle for tipping the vessel. When the plate is affected, forward travel is Press up to tip off and down to lower the bed. activated, so that the operator does not run the 2) Control handle for High tip function.
User Manual HG H1000 HIGH TIP The functional units of the machine 15. Recoil start. Used to start in the event of a power failure. 16. Filling of hydraulic oil Releaser. If the release lever is pushed down, the motor is disconnected and the machine can be pushed.
User Manual HG H1000 HIGH TIP WARNING! Precautions before starting Petrol is a highly flammable and explosive liquid. Leave the machine to cool for at least 10 min. Check engine condition before filling and keep it away from ignition sources.
Page 14
User Manual HG H1000 HIGH TIP Tyre pressure and retightening: Safety plate test All tyres must have the right air pressure in order to ensure optimum ergonomics. Tyre pressure, drive wheel: 85 psi/8.5 bar Tyre pressure, guide wheels: 71 psi/7.1 bar...
User Manual HG H1000 HIGH TIP Before reversing, check for people and 4. Driving obstacles behind you. The direction of the machine is controlled by pulling the handle bar to the right or left while the machine is moving forward. Do not attempt to...
Page 16
User Manual HG H1000 HIGH TIP tipping lever with your left hand, while keeping container cannot rise right, release the your right hand on the handle bar. Wait until the switch again. • tray is lowered completely, and place both...
User Manual HG H1000 HIGH TIP 5. Maintenance 5.1 Overview of maintenance For each xx operating hours Activity Daily 3 m. hours hours hours hours Hydraulic oil level Engine oil level Air filter (in a very dusty environment) Check Wheel air pressure...
User Manual HG H1000 HIGH TIP HG does not recommend Towing and tipping in leaving the machine in case of engine failure disconnected mode. With the help of two people, the container can be tipped to the side. High Tip does not need to be raised as shown in figure pos.
User Manual HG H1000 HIGH TIP WARNING! Draining hydraulic oil In this case, it must always be ensured that the Place a suitable container under the hydraulic oil container is tipped at least 125* degrees above tank and remove the plug. The tank must be the horizontal surface where the container has able to hold 17 liters.
Page 20
User Manual HG H1000 HIGH TIP Changing the engine oil Air filter Place a suitable container under the hydraulic oil Remove the cover and filter by loosening the tank and remove the plug. Clean the plug, two finger nuts. replace the gasket and refit the plug when the oil Clean the foam filter and paper filter with has been drained from the tank.
Page 21
User Manual HG H1000 HIGH TIP Lubrication Retightening the wheels Standard high-pressure grease can be used for Retighten the wheels once a week. lubrication. Tightening torque: 100 Nm. Lubricating nipples are mounted on: Replacement of signs • Guide wheel suspension, rocker shaft.
Page 22
User Manual HG H1000 HIGH TIP Adjusting the zero point Adjustment of safety plate The machine's zero point ensures that the Pressing the safety plate should move the machine stands still when the forward/reverse machine forward, preventing the operator from handle is not activated.
Page 23
User Manual HG H1000 HIGH TIP Adjusting the tipping lever The stop on the tipping lever reduces the speed of the lowering function to prevent the hose burst check valve from being activated. Adjust the stop so that the load is lowered at an even speed, but the engine does not sound strained.
User Manual HG H1000 HIGH TIP Problem Possible cause Solution The machine will not start. The oil guard is activated. Check oil level and top up. The machine will not pull. The freewheel valve is activated. Push in the freewheel button and turn clockwise to lock.
User Manual HG H1000 HIGH TIP Technical specifications Specifications Width 850 mm Length 2050 mm Height 1080 mm Own weight 415 kg Content in liters 400 L Content in kg 1000 kg Reading height 125 cm Driving speed 0-6 km/t...
Warranty period shown to the manufacturer or its representative HG Machines provides a guarantee for 12 within two weeks after the damage has months. The warranty period begins on the date occurred. Owner rights to the damaged part(s) of delivery.
User Manual HG H1000 HIGH TIP EU declaration of conformity Hedensted, 15. februar 2023 HG Machines ApS Vejlevej 15 DK-8722 Hedensted Tel. (+45) 75 89 12 44 Nikolaj Birkerod www.hg-machines.com Direktør hereby declares that: Super Skub model HYDRA with recoil start...
Need help?
Do you have a question about the H1000 HIGH TIP and is the answer not in the manual?
Questions and answers